587557
6
Zoom out
Zoom in
Previous page
1/16
Next page
6
1 Button "Power"
The unit is switched on or off with this button.
2 Button "Mode"
This button is used to switch the unit to the desired
operating mode. There are three operating modes
available. The signal lights of display 11 indicate the
selected operating mode.
The order is:
Cooling mode: "Cool" signal light
In this operating mode, the unit cools the room to
the set value. The temperature can be set in a
range between 16 and 32 °C. The fan speed can
be freely selected.
Dehumidification mode: "Dehumidifier" signal light
In this operating mode, the unit dehumidifies the
room. The temperature can be set in a range be-
tween 16 and 32 °C. The "Med" fan speed is pre-
set and cannot be changed.
Ventilation mode: "Fan" signal light
In this operating mode, the unit is used to circu-
late air with no cooling effect. The temperature
cannot be set. The fan speed can be freely se-
lected.
3 Button "Fan Speed"
This button can be used to select a fan speed in the
cooling and ventilating operating modes. Each time
the button is pressed, the speed of the fan changes.
The signal lights of display 10 indicate the selected
speed.
The order is:
Highest fan speed: "High" signal light
Medium fan speed: "Med" signal light
Lowest fan speed: "Low" signal light
4 Button "Timer"
This button can be used to automatically activate the
unit to switch off or on. The signal light 9 indicates
whether the timer is activated.
Control panel
4
3
2
1
7 11 10 6 12
5
8 9
5 Buttons Up/Down "Timer/Temp Adjust"
These buttons can be used to select the desired tar-
get temperature in the cooling and dehumidifying op-
erating modes. If one of the up/down buttons 5 is
pressed, the signal light 7 disappears and the signal
light 8 lights up.
The display now shows the target temperature in-
stead of the room temperature. The target tempera-
ture can be set in a range between 16 and 32 °C in
1°C increments by pressing the buttons 5.
Left button = Higher target temperature.
Right button = Lower target temperature.
In addition, the up/down buttons 5 can be used to
change the timer period for switching on and off in
all operating modes.
Left button = Longer time period.
Right button = Shorter time period.
6 Display
The room temperature measured by the internal
sensor of the unit is shown on the display.
If one of the up/down buttons 5 is pressed, the dis-
play switches to show the set target temperature.
If the timer button 4 is pressed, the display switches
to show the remaining number of hours until the unit
will be switched on or off.
If after 15 seconds, no buttons are pressed, the
room temperature appears on the display again.
7 Signal light "Room Temp"
This light indicates that the measured room tempera-
ture is shown on display 6.
8 Signal light "Set Temp"
This light indicates that the currently set target tem-
perature is shown on display 6.
9 Signal light "On/Off"
This light indicates whether a timer has been acti-
vated. It blinks if is possible to make an entry using
the up/down buttons 5.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO MKT260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO MKT260 in the language / languages: English as an attachment in your email.

The manual is 1,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO MKT260

REMKO MKT260 User Manual - German - 16 pages

REMKO MKT260 User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info