Manual REMKO ELT18-HT (page 5 of 24) (English)

794473

Zoom out

Zoom in

1/24

1.6 Safety instructions for the oper-

ator

The operational safety of the units and compo-

nents is only assured providing they are used as

intended and in a fully assembled state.

nThe personnel tasked with operating the units

must check the units for visible defects on the

operating and safety devices as well as the

presence and function of the protective devices

prior to starting work.

If defects are discovered these must be

reported to the supervisor!

nIn the event of defects that endanger the

operational safety of the unit, operation must

be discontinued immediately.

nDo not operate units or components with

obvious defects or signs of damage.

nThe units must not be left unattended during

operation.

nObserve the respective local regulations and

the relevant electrical safety measures when

using the units.

nThe relevant safety guidelines of the Employ-

er's Liability Insurance Association or property

insurer must be observed.

nSafety devices must not be bypassed or disa-

bled.

nThe units may not be installed or operated in

potentially flammable or explosive environ-

ments.

nThe units must not be operated in locations

where:

Combustible gaseous, air or dust-air mixtures

could be produced; flammable small parts

could be sucked in, set alight on the heating

coil and blown out in a glowing state.

nMaintain safety distances to combustible mate-

rials;

0.5 m on the sides and suction side

2.0 m outlet side

nThe units must be installed in a stable position

and must not topple over or slide out of posi-

tion during operation.

nNever insert foreign objects into the units.

nThe units must not be covered during opera-

tion.

nAn unobstructed air inlet and air outlet must be

guaranteed at all times.

nThe units must not be operated in the vicinity of

bathtubs, showers, swimming pools etc.

nThe units must not be operated directly below

a wall socket.

nThe units must not be operated in an environ-

ment with an ambient temperature of over

60 °C.

nThe units and components must not be

exposed to any mechanical load, extreme

levels of humidity or extreme temperatures.

nNever allow water to enter the units.

nProtective covers (grilles) over moving parts

must not be removed from units that are in

operation.

nContact with equipment parts or components

can lead to burns or injury.

nAll housing parts and unit openings, e.g. air

inlets and outlets, must be free from foreign

objects.

nThe air outlet must not be constricted or

equipped with pipe or hose lines.

nAll electrical cables for the units must be pro-

tected against damage, including damage

caused by animals.

nExtensions to the connection cable must only

be conducted by authorised specialist electri-

cians, taking into consideration the unit

capacity, cable length and local use.

nFlooring and ceilings must be fire retardant.

nThe units must be inspected by a service tech-

nician to ensure that they are safe to use and

fully functional at least once yearly. Visual

inspections and cleaning may be performed by

the operator when the units are disconnected

from the mains.

1.7 Safety notes for installation,

maintenance and

inspection work

nThe units and components may only be set up,

installed and maintained by qualified per-

sonnel.

nAppropriate hazard prevention measures must

be taken to prevent risks to people when per-

forming installation, repair, maintenance or

cleaning work on the units.

nThe setup, connection and operation of the

units and its components must be undertaken

in accordance with the usage and operating

conditions stipulated in this manual and comply

with all applicable regional regulations.

nRegional regulations and laws must be

observed.

nThe units must be installed and operated in

such a way that personnel are not endangered

by warm air and radiant heat and that no fires

can occur

nA safety zone of 1.5 m should be maintained

around the units - including non-combustible

items

nThe power supply should be adapted to the

requirements of the units.

nMobile units must be set up securely on suit-

able non-combustible surfaces.

nThe units and components should not be oper-

ated in areas where there is an increased risk

of damage. Observe the minimum clearances.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of REMKO ELT18-HT in the language / languages: English as an attachment in your email.

The manual is 4.06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO ELT18-HT

REMKO ELT18-HT User Manual - German - 24 pages

REMKO ELT18-HT User Manual - Dutch - 24 pages

REMKO ELT18-HT User Manual - French - 24 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

REMKO ELT18-HT Manual

Product: