587892
7
Zoom out
Zoom in
Previous page
1/16
Next page
7
Observe the regular care and
maintenance intervals
In accordance with the
operating conditions, the units
must, if necessary, be checked
at least yearly by a specialist
to ensure that they are in
a condition that is safe to use
Keep the units free of dust and
other debris
Only clean the units with a dry
or lightly moistened cloth
Never subject to direct jets of
water.
e.g. pressure washers etc.
Never use abrasive or solvent-
based cleaners
Use only suitable cleaners, even
for heavy contamination
Check the inlet and outlet grille
for contamination on a regular
basis
Care and maintenance
The unit (fan) does not start.
1.
Check the mains fuses on site.
2. Check the power plug.
3. Check the operating switch.
4. Check that the fan can move
freely.
The unit does not heat up.
1.
Check the operating switch.
2. Check that the contactor is
functioning correctly.
3.
Check that the temperature
limiter or capillary tube are
functioning correctly and check
for damage.
4.
Check whether the thermostat
or strapping plug are plugged
in.
5.
In case of unit operation
with a room thermostat, set
the thermostat to a value
that is higher than the room
temperature.
If all of the functional checks
have been carried out without
any findings, please contact an
authorised service station.
Troubleshooting
Check the safety equipment
and protective devices on
a regular basis
Be careful not to damage the
probe or capillary tube of the
temperature limiter when
removing or mounting the
protective outlet grille
NOTE
Setting and maintenance
work may only be carried out
by authorised and qualified
technicians.
CAUTION
Before undertaking any work
on the units, the power plug
must be removed from the
mains socket.
NOTE
Regular care and maintenance,
at the latest after every
heating period, is the basic
requirement for a long service
life and malfunction-free
operation of the units.
CAUTION
An electrical safety check must
be carried out in accordance
with VDE 0701 after any work
on the units.
NOTE
Replace defective or damaged
parts immediately and
exclusively with original spare
parts.
Checking
The strapping plug supplied with
the device is used for maintenance
or testing according to VDE 0701.
Follow the steps below to check.
1. Connect the supplied strapping
plug [2] to the thermostat
socket [1] on the unit.
2. Check the device.
3. Remove the strapping plug
1
2
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO ELT 10-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO ELT 10-6 in the language / languages: English as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO ELT 10-6

REMKO ELT 10-6 User Manual - German - 16 pages

REMKO ELT 10-6 User Manual - Dutch - 12 pages

REMKO ELT 10-6 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info