587883
5
Zoom out
Zoom in
Previous page
1/20
Next page
5
Monitoring operation of device
All functions of the unit are fully automatic and moni-
tored for safety by the safety facility and the automatic
burner relay (part of the forced-air burner).
If the flame burns irregularly or goes out, the unit is
switched off by the automatic burner relay. The control
lamp on the control panel and the malfunction lamp of
the automatic burner relay light up.
Before the unit can be restarted, the automatic burner relay
must be released by pressing the external reset button on
the operating panel or the reset button on the automatic
burner relay.
The fan control (TR) regulates operation of the fan. The
temperature monitor (TW) limits or regulates the tem-
perature of the unit in heating mode.
The safety temperature limiter (STB) interrupts heating
mode when extreme overheating occurs or if the tem-
perature monitor (TW) stops working or is defective.
The STB can only be manually released after the unit
has cooled down.
G
Before the STB is released to begin operation
again, the reason the STB was activated must be
determined.
Installation Requirements
The heaters may only be installed in compliance with
the relevant regulations, in particular, regulations gov-
erning the installation and operation of fireplaces and
furnaces.
Any national/regional emission control laws or regula-
tions must also be observed.
à Avoid under- or overpressure in the room where the
unit is installed, as this would result in combustion
troubles.
à Make absolutely sure that the opening for air intake
and output is adjusted to the fan power (see model
plate).
If this is not possible, the burner has to be equipped
with a separate air supply device to ensure optimum
combustion.
Installation in closed, well aerated rooms without
connection to a chimney
à The units may only be operated when the minimum
amount of air required for combustion is supplied.
à A safe exhaustion of the waste gases is to be en-
sured to exclude inadmissible pollution.
- Fresh air is supplied from below.
- Waste gases are expelled upwards.
Outside installation
à Operation of the unit may not have any harmful ef-
fects or cause any unreasonable problems.
à The unit operator must ensure that unauthorised per-
sons are prevented from manipulating the unit or its
power supply.
à Because rain and snow can be sucked in by the air
supply fan, a suitable protective covering should be
used.
Heating Rooms
à Warm air generators may only be operated with a
room thermostat when heating rooms.
Accessories.
à Make sure that there is enough fresh air to ensure
optimum combustion.
Safety zones
à To ensure safe operation and guarantee unhindered
access to the unit for maintenance work, a safety
zone of 1.5 m should be maintained around the unit.
à Floors and ceilings must be fire-resistant.
Electrical Connection
à The units are operated with 400 V / 3~N / 50 Hz.
à The unit must be connected to the power source at a
special terminal equipped with a switch to protect
against faulty currents.
à Extension cable may only be laid by authorised elec-
tricians based on the capacity of a unit, the length of
the cable and in accordance with local requirements.
à All extension cable may only be used once they have
been unrolled.
G
While the unit is in operation, the safety features
may not be bypassed or blocked!
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for REMKO CLK50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of REMKO CLK50 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of REMKO CLK50

REMKO CLK50 User Manual - German - 20 pages

REMKO CLK50 User Manual - Dutch - 16 pages

REMKO CLK50 User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info