425028
4
Zoom out
Zoom in
Previous page
1/8
Next page
Face ava nt
Face arrière
Vorderseite
Rückseite
Front Panel
Rear Panel
4
Bezeichnungen:
1. Lautstärkeregler für Mikrofon
2. 2-fach Equalizer für Mikrofon
3. Gain-Regler für Kanal 1 und 2
4. 3-fach Equalizer für Kanal 1 und 2
5. Aussteuerungs-LEDs für Mastersignal
6. Aussteuerungs-LED für Cuesignal
7. Lautstärkeregler für Masterausgang
8. Lautstärkeregler für Kopfhörer
9. Cue-Auswahl Schalter
10. Signal-Eingangswahlschalter für Kanal 1 und 2
11. Cue-Mix Fader
12. Linefader für Kanal 1 und 2
13. Crossfader Reverse Schalter
14. Crossfader Curve Regler
15. Crossfader
16. EIN/AUS Schalter
17. Eingangsbuchse für Mikrofon (6,3 mm Klinke)
18. Ausgangsbuchse für Kopfhörer (6,3 mm Klinke)
19. GND Erdungsschrauben
20. Eingangsbuchsen für Kanal 1 und 2 (Cinch)
21. Phono/Line Umschalter für Kanal 1 und 2
22. REC Ausgangsbuchsen (Cinch)
23. Master Ausgangsbuchsen (Cinch)
24. Eingang für externes Netzteil
Anschlüsse
1. Verbinden Sie Ihre Linequellen (CD-Player, MiniDisc, DAT, etc.)
und Ihre Plattenspieler mit den Eingangsbuchsen für Kanal 1
und 2 -20-. Wenn Sie an die "Phono"-Buchsen Plattenspieler
anschließen möchten, so stellen Sie den/die Phono/Line
Umschalter -21- in die Position "Phono"; möchten Sie an diese
Buchsen Linequellen anschließen, so stellen sie den/die
Phono/Line Umschalter in die Position "Line".
ACHTUNG! Stellen Sie sicher, dass während der
Betätigung der Phono/Line Umschalter das Gerät
ausgeschaltet ist.
2. Verbinden Sie die Erdungskabel Ihrer Plattenspieler mit der
jeweiligen GND Erdungsschraube -19-.
3. Verbinden Sie Ihr Mikrofon mit der Eingangsbuchse Mic -17-.
4. Verbinden Sie Ihren Kopfhörer mit der Ausgangsbuchse für
Kopfhörer -18-.
5. Verbinden Sie Ihre Hauptanlage je nach Bedarf mit den Master
Ausgangsbuchsen -23- (Cinch).
6. Verbinden Sie ein Aufnahmemedium Ihrer Wahl mit den REC
Ausgangsbuchsen -22-.
7. Schließen Sie das externe Netzteil an den entsprechenden
Eingang -24- an.
Designation:
1. Volume control for microphone
2. 2-fold equalizer for microphone
3. Gain control for channels 1 and 2
4. 3-fold equalizer for channels 1 and 2
5. Modulation LEDs for master signal
6. Modulation LED for cue signal
7. Volume control for master output
8. Volume control for headphones
9. Cue selector
10. Signal input selector for channels 1 and 2
11. Cue Mix Fader
12. Line fader for channels 1 and 2
13. Crossfader reverse switch
14. Crossfader curve switch
15. Crossfader
16. ON/OFF switch
17. IN socket for microphone (6.3 mm jack plug)
18. OUT socket for headphones (6.3 mm jack plug)
19. GND grounding screws
20. IN sockets for channels 1 and 2 (cinch)
21. Phono/Line change-over switch for channels 1 and 2
22. REC OUT socket (cinch)
23. Master OUT socket (cinch)
24. Input for external power pack
Connections
1. Connect your line sources (CD player, MiniDisc, DAT, etc.) and
your turntables with the input jack for channels 1 and 2 -20-. If
you wish to connect (a) turntable(s) to the "Phono" jacks switch
the phono/line change-over switches -21- to the
"Phono"-position. If you intend to hook up (a) line source(s) to
these jacks simply switch the phono/line change-over switch to
the "Line"-position.
ATTENTION! When operating the phono/line change-over
switches always make sure that the unit is switched of.
2. Connect the ground cable of your turntables with the
respective GND ground screw -19-.
3. Connect your microphone with the Mic input jack -17-.
4. Connect your headphones with the output jack for
headphones -18-.
5. Connect your main unit according to your requirements with
the Master output jacks -23- (cinch).
6. Connect the recording equipment of your choice with the REC
output jacks -22-.
7. Hook up the external power pack with the respective
input -24-.
Désignation:
1. Régleur de volume du microphone
2. Égaliseur 2 voies du microphone
3. Régleur de gain pour les canaux 1 et 2
4. Égaliseur 3 voies pour les canaux 1 et 2
5. DEL de saturation du signal Master
6. DEL de saturation du signal Cue
7. Régleur de volume de la sortie Master
8. Régleur de volume du casque
9. Sélecteur Cue
10. Sélecteur du signal d'entrée pour les canaux 1 et 2
11. Curseur Cue-Mix
12. Curseur linéaire pour les canaux 1 et 2
13. Touche Crossfader Reverse
14. Régleur de courbe du Crossfader
15. Crossfader
16. Interrupteur MARCHE/ARRÊT
17. Fiche d'entrée du microphone (6,3 mm jack)
18. Fiche de sortie du casque (6,3 mm jack)
19. Vis de terrage GND
20. Fiches d'entrée pour les canaux 1 et 2 (Cinch)
21. Commutateur Phono/Line pour les canaux 1 et 2
22. Fiches de sortie REC (Cinch)
23. Fiches de sortie Master (Cinch)
24. Connecteur du bloc d'alimentation externe
Connexions
1. Connectez vos sources Line (lecteur de CD, MiniDisc, DAT, etc.)
et votre platine vinyle avec les fiches d'entrée pour les canaux
1 et 2 -20-. Si vous désirez connecter une platine vinyle aux
connecteurs "Phono", il faut régler les commutateurs
Phono/Line -21- sur la position "Phono"; si vous désirez
connecter des source Line, réglez les commutateurs
Phono/Line sur la position "Line".
ATTENTION ! Avant de régler les commutateurs
Phono/Line, contrôler si l'appareil est éteint !
2. Branchez le câble de mise à terre de votre platine vinyle sur la
vis de terrage GND respective -19-.
3. Connectez votre microphone sur la fiche d'entrée Mic -17-.
4. Connectez votre casque sur la fiche de sortie casque -18-.
5. Connectez votre chaîne selon vos besoins sur les fiches de
sortie Master -23- (cinch).
6. Connectez votre appareil d'enregistrement de votre choix sur
les fiches de sortie REC -22-.
7. Raccordez le bloc d'alimentation externe à son entrée -24-.
17 18
ACCESS2_IM.qxp 22.01.2008 17:09 Uhr Seite 4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Reloop access 2 mengpaneel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Reloop access 2 mengpaneel in the language / languages: English, German, French as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info