802111

Ratio MP16-10-KX Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
Safety regulations and measures
1. The electrical installation must be switched off during installation.
2. Install the power-inlet according to the stated instructions and directions in the
manual.
3. Use cables with appropriate wire size. See table “WIRE SIZE”.
4. Connections and safety features must be executed according to the locally
applicable regulations.
Things you need for installation
• Pencil
• Electric drill
• Hole saw
• 4,5mm or 1/8 drill bit
• Small flat blade screwdriver
• 2.5mm hexagonal socket wrench for the 4mm SS screws
• Cutting / wire stripping pliers
Installation direction
To install the power-inlet, proceed as follows:
1. Make a cut out in ship’s hull using the outline drawings of figure 1.
2. Remove the rear safety enclosure from the inlet.
3. Pull internal wiring through the hull opening.
4. Thread the wiring through the strain relief on the rear safety enclosure. Slide the
mounting gasket over the wiring.
5. Back off terminal screws on the rear housing of the inlet.
6. Dismantle cable 50 mm, cut back green/yellow wire for 20 mm, strip wire ends 6
mm. Make sure the wire strands are clean and not corroded. If necessary, cut back
the wire until clean wire is uncovered. Do not solder the ends of the wire!
7. Insert wires into the proper colour coded terminal openings (see table
“specifications” for the proper colour codes) on the back of the inlet. Tighten
terminal screws to 1.6-2.2Nm (14-20 in.-lbs.) torque. Make certain there is no wire
insulation under any terminal.
8. Slide the rear safety enclosure onto the back of the inlet.
9. Position the gasket and inlet over the hull opening, align the mounting holes and
attach the inlet to the hull with screws. Install the inlet with the M4 screws
included.
SPECIFICATIONS
General
MP16-10-K
MP16-10-KX
Ø Connections:
2p + E
2p + E
Ø Voltage:
230 V
230 V
Ø Maximum current (Amps):
16A / 230V
16A / 230V
Ø Protection degree:
IP 56 (IEC529)
IP 56 (IEC529)
Ø Marking:
CE
CE
Materials
Ø Cap and bezel
PA6 glass filled
PA6 glass filled chrome
plated
Ø Contact blades / terminal parts:
Nickel plated brass
Ø Plug body:
PA6, V0 quality
COLOUR CODES
Function:
Wire colour:
Terminal colour code:
PE (ground)
Yellow / green
Green
N (neutral)
Blue
Blue
L1 (phase, load)
Brown or black
Brown
WIRE SIZE
Voltage (Volts)
Current (Amps)
Cross section
American Wire Gauge
230 V AC
16 A
2.5 mm²
AWG 14
\NGLISH
Veiligheidsvoorschriften en –maatregelen
1. Gedurende de installatiewerkzaamheden moet de elektrische installatie
spanningsloos zijn.
2. Monteer de landaansluiting volgens de voorschriften en aanwijzingen in dit
montagevoorschrift.
3. Gebruik kabels met voldoende aderdoorsnede: zie tabel “WIRE SIZE”.
4. Aansluitingen en beveiligingen moeten in overeenstemming met de plaatselijk
geldende voorschriften worden uitgevoerd.
Dit heeft u nodig voor de installatie
• Potlood
• Boormachine
• Gatenzaag
• 4,5mm boortje
• Kleine platte schroevendraaier
• 2.5mm inbussleutel voor de meegeleverde M4 RVS schroeven
• Kniptang en striptang
Installatievoorschrift
Ga bij de installatie van de contactdoos als volgt te werk:
1. Maak aan de hand van de inbouwmaten in afbeelding 1 een uitsparing in de
scheepswand.
2. Verwijder de isolatiekap aan de achterzijde van de contactdoos.
3. Trek de bedrading door de isolatiekap.
4. Voer de bedrading door de trekontlasting van de isolatiekap. Plaats de rubberen
montage pakking over de bedrading.
5. Draai de schroeven van de aansluitklemmen aan de achterzijde van de contactdoos
een paar slagen los.
6. Ontmantel de isolatie van de kabel over 50mm, en knip de geel/groene ader 20mm
terug. Strip de draadeinde 6mm. Let er op dat de aders blank zijn en niet
gecorrodeerd. Zonodig de bedrading inkorten en de kabel opnieuw strippen. De
aders mogen niet vertind worden!
7. Sluit de aders op de juiste aansluitklemmen aan de achterzijde van de contactdoos
aan (zie tabel “specifications” voor de juiste kleurcodes). Draai de schroeven van
aansluitklemmen goed aan. (1.6-2.2Nm). Let er op dat er geen isolatie onder de
aansluitklemmen zit.
8. Monteer de isolatiekap aan de achterzijde van de contactdoos.
9. Plaats de rubber pakking tezamen met de contactdoos zodanig in de uitsparing in de
scheepswand dat de montagegaten op de juiste plaats zitten. Bevestig de
contactdoos op de scheepswand met behulp van de meegeleverde vier M4-
schroeven.ENGL
ENGLISH
SPECIFICATIONS
WARNING:
THIS INLET IS INTENDED FOR BOATS WIRED FOR THE EUROPEAN MARKET.
RATING: 16A/230VAC (50Hz)
.........................................................................................................................................................................................................................................................................................................................................................................
THE REQUIREMENTS FOR INSTALLATION OF ELECTRICAL SYSTEMS ON CRAFT OF HULL
LENGTH UP TO 24M ARE SPECIFIED IN THE ISO 13297 STANDARD.
!
!
A
55 mm
B
4,5mm
C
50 mm
Ratio Electric B.V. Ambachtsstraat 12, NL-3861 RH Nijkerk, The Netherlands.
Tel.:
+31-33-2452360
Email:
info@ratio.nl
Web:
www.ratio.nl Version MP006 1/2016
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ratio MP16-10-KX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ratio MP16-10-KX in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0.67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info