685862
1
Zoom out
Zoom in
Previous page
1/2
Next page
CHANGING A NOZZLE
1. REMOVING THE NOZZLE RETENTION SCREW
Use your K-Key (K) or a small flat blade screwdriver to remove
the nozzle retention screw (C) by turning counter-clockwise to
remove and clockwise to re-install.
2. PULL UP THE RISER
Insert the K-Key (K) in the keyhole (D) on the top of the nozzle
turret (M) and turn the key ¼ turn to insure that the key does
not slip out of the keyhole when you pull it up. Firmly pull up
the entire spring-loaded riser to access the nozzle socket (N).
Hold the riser assembly with one hand.
3. REMOVING THE NOZZLE
Insert the end of the K-Key (K), hook side up, into the tall slot
along the right side of the nozzle (J) and pull up to pop out the
nozzle. NOTE: Do not put the K-Key or any instrument into the
nozzle opening.
4. INSTALLING A NOZZLE
Press the desired nozzle into the nozzle socket (N). Make sure
the nozzle number is visible and the nozzle “wing” is up.
Then, re-install the nozzle retention screw (C).
NOTE: The nozzle retention screw is also a break-up screw
and used to adjust the distance of the spray.
SETTING THE ARC ADJUSTMENT
1. FINDING THE LEFT START POSITION
Place your finger on the top center of the nozzle turret (M).
Rotate the turret to the right until it stops and then back to
the left until it stops. Notice the position of the nozzle arrow.
This is the “Left Start” (L) position. The sprinkler will begin
spraying from this position and rotate clockwise until it
reaches the right “Arc Stop” (F).
2. ORIENTING THE LEFT START POSITION
Insert the K-Key (K) in the keyhole (D) on the top of the nozzle
turret (M) and turn the key ¼ turn to insure that the key does
not slip out of the keyhole when you pull it up. Being careful
not to allow the nozzle turret to turn, firmly pull up the entire
spring-loaded riser. Hold the lower riser assembly up with
one hand. Now turn only the lower riser (O) clockwise or
counter-clockwise until the nozzle arrow is pointing where
you want the sprinkler to begin spraying.
3. CHANGING THE ARC
Insert K-Key (K) or a flat blade screwdriver into the Arc Set
Adjustment slot (I). Turn clockwise to increase the arc or
counter-clockwise to decrease the arc. NOTE: The arc set
arrow in the center of the nozzle turret rotates to show
the correct setting.
Ra Flow
K L/M M
3
R F
GP
D
A
B
C
Ra Flow
K L/M M
3
R F
GP
I
G
H
30° – 360°
Ra Flow
K L/M M
3
R F
GP
A TURRET TOP
ARC SELECTION:
30° TO 360°
Nozzle
Position
Keyhole
Arc Set
Adjustment
K K-KEY
J NOZZLE
Nozzle
Retention
Screw
MINIPRO
GEAR DRIVEN SPRINKLER SETTING INSTRUCTIONS
NOTE: The MiniPro is factory preset with a 40° arc setting, and includes a pre-installed #1.5 nozzle.
B
C
D
Arc Set
Arrow
Arc’s
Adjustable
Range
E
F
G
Ra Flow
K L/M M
3
R F
GP
Q
R
S
Housing
Can
Sprinkler
Assembly
Twist-Lock
Top
Q
R
S
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for RAINBIRD MiniPro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of RAINBIRD MiniPro in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info