500584
1
Zoom out
Zoom in
Previous page
1/4
Next page
Installatie instructies / Installation instruction / Notice de montage
5580
3/4” Eurokonus
3/4” eurocone
L
210
55
Ø
62
55
C
A
B
1“
A [mm] 39
Vertrek / Supply / Départ
A [inch] 1,54
B [mm] 64
1“
B [inch] 2,52
C [mm] 86
G 1“
C [inch] 3,39
G 1“
Retour / Return / Retour
Onder voorbehoud van technische wijzigingen / subject to technical modification / sous réserve des modifications techniques
Groepen / outlets / boucles 2 3 4 5 6 7 8 9 10 11 12
L [mm] 190 245 300 355 410 465 520 575 630 685 740
L [inch] 7,48 9,65 11,81 13,98 16,14 18,31 20,47 22,64 24,80 26,97 29,13
I. Montage verdeler / Assembly of the manifold / Montage de distributeur :
De consoles van verdeler zijn
gemonteerd op de C-rails van de
verdeelkast of op de wand. De
bolkranen met vlakke dichting en losse wartel
worden op de verdeler gemonteerd. De
lichamen van de verdeler zijn elk uitgerust met
een mannelijke metrische draad van 1". Alle
originele onderdelen kunnen worden
gemonteerd dmv vlakke afdichtingen met
afdichtingring. We zijn niet aansprakelijk en
bieden geen garantie indien er onderdelen van
externe herkomst worden gebruikt.
Voor de aansluiting van de leidingen op de
verdeler verwijzen we naar hoofdstuk II:
‘Installatie van de leidingen’.
Voor het spoelen en vullen van het
verwarmingscircuit moeten er slangen met een
mondstuk van 1/2" of 3/4" op de mannelijke
draad van de vulkraan worden geschroefd. Om
de vul- en of aflaatkraan te openen of te sluiten
moet er aan de hendel of de vierkantnaaf
worden gedraaid. Elk circuit moet afzonderlijk
worden gespoeld/gevuld. Er mag alleen in de
richting van de stroom worden gespoeld. Een
te hoog drukverschil (>1 bar) moet worden
vermeden. De verdeler moet met
verwarmingswater conform VDI 2035 worden
gebruikt. Leef de instructies voor het
vloerverwarmingssysteem na. De identificatie
van de verwarmingscircuits (groepen) gebeurt
aan de hand van zelfklevende etiketten op de
verdeelblok. De dichtheid en de goede werking
van de verdeler werden in de fabriek getest. De
testdruk bedroeg 6 bar. Het sluitingspunt van
de kleppen is 11,8 mm.
NL
The brackets of the heating mani-
fold are mounted to the moveable
C- rails via the prepared bolts or
boreholes. Please follow the respective mount-
ing instructions. The HKV should be mounted
with the optional ball valve set. The manifold
pipes are each fitted with a 1” male thread for
mounting of the ball valves / filling set. These
original parts can be mounted as self-sealing
parts washers. We cannot assume liability or
extend any warranty if external parts are used.
For pipe connection to the manifold please pay
attention to chapter II: "Installation of pipes".
Flushing and filling the heating circuits
To flush and fill the heating circuits, fit hoses
with ½“ or ¾” hose nozzles to the male thread
of the filling cocks. Open / close the cocks by
turning the handle or square hub.
Each circuit should be flushed separately. Avoid
high pressure difference (> 1 bar). The manifold
should be operated with water accordingly to
VDI 2035. Please Pay attention to the instruc-
tions of the floor heating system.
GB
The heating circuits can be identified by attach-
ing self-adhesive labels to the manifold block.
This ensures correct assignment of the outlets
of the manifold to the various rooms.
The manifolds are factory-tested for seal-
tightness (using the differential pressure
method) and proper functioning. The testing
pressure for the manifolds is 6 bar / 87 psi.
The closing point of the valves is 11.8 mm.
Les consoles du collecteur sont
fixées sur les profilés en C coulis-
sants, sur les boulons ou les
perçages préparés. Veuillez tenir compte des
instructions d'assemblage correspondantes. Le
distributeur est fourni, en fonction de l'étendue
de l’installation, avec un jeu de vannes à bois-
seau sphérique et/ou un jeu de remplissage.
Les raccords du collecteur possèdent tous un
filet extérieur de 1" pour assurer l'assemblage
des vannes à boisseau sphérique / du jeu de
remplissage. Les accessoires d'origine peuvent
être assemblés par joint torique assurant une
auto étanchéité. Une garantie ne peut pas être
octroyée en cas d'utilisation d'articles d'autres
entreprises /marques.
Pour le raccordement des tubes aux pièces de
raccord vissé, veuillez observer les instructions
d'assemblage des tubes.
Rinçage et remplissage des circuit de chauf-
fage. Pour rincer et remplir les circuit de chauf-
fage, des tuyaux sont vissés a l’aide de rac-
cords de ½" et/ou ¾".Les vannes de remplis-
sage et de rinçage peuvent être ouverte et
fermé au moyen des prises d'aile. Rincer cha-
que circuit séparément dans le sens du flux.
Des différences de pression (> 1 bar) doivent
être évitées. Le distributeur doit être alimenté
avec de l'eau de chauffage conformément à
VDI 2035. Les circuits de chauffage peuvent
être repérés par des étiquettes autocollantes a
posées sur le tronc du collecteur. De cette
manière, il est possible d'assurer une assigna-
tion univoque des sorties du collecteur vers
chaque local individuel. Les collecteurs sont
soumis départ usine à un essai d'étanchéité,
par la méthode d'essai de pression différen-
tielle, ainsi que fonctionnel. La pression d'essai
des collecteurs est de 6 bar. La cote de ferme-
ture des vannes est de
F
11,8 mm.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Radson Verdeler at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Radson Verdeler in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info