491304
4
Zoom out
Zoom in
Previous page
1/25
Next page
6
ENGLISH
7
OFF: The unit is permanently switched on.
ON: The unit switches on automatically, if a music signal is received and auto-
matically switches to stand-by mode after approximately 15 minutes, if no
music signal is received.
Units with POWER switch for stand-by only:
The switch operates as follows:
ON: The unit is permanently switched on.
AUTO: The unit switches on automatically, if a music signal is received and auto-
matically switches to stand-by mode after approximately 15 minutes, if no
music signal is received.
OFF: The functions are switched off.
Units with POWER switch for mains only:
If the mains POWER switch is in OFF position, the unit is turned off completely.
If the mains POWER switch is in ON position, the unit is in automatic mode. I.e. if a music
signal is received, the unit switches from stand-by mode to operation mode (ON) and switches
back to stand-by mode, if no music signal is received for approximately 20 minutes.
Connecting up
Before connecting up the subwoofer to your hi-fi or surround system, make sure that the unit
and all system components are switched off, i.e. the pilot lights should all be off.
Connection variant no. 1
(Subwoofer/satellite system for hi-fi and surround)
First take one of the 3m loudspeaker cables supplied with your subwoofer and connect it
to the left-hand speaker output of the amplifier and the left-hand input (HIGH LEVEL) of the
subwoofer. The red „+“ terminal of the amplifier must be wired to the red „+“ terminal of the
subwoofer; the amplifier’s black „-“ terminal must be wired to the black „-“ terminal of the sub
-
woofer. The „+“ line is always coloured red or marked accordingly on speaker cables. Now
repeat the procedure with the second loudspeaker cable to connect the amplifier’s right-hand
speaker output with the subwoofer’s right-hand input. Here too, please take particular care
to ensure that the cables are connected up with the correct polarity, i.e. the red „+“ terminal
of the subwoofer connected to the red „+“ terminal of the amplifier, the black „-“ terminals
connected to each other likewise. By doing so, you will avoid considerable impairment of the
sound as a result of incorrect polarity.
Having connected up your subwoofer at the front-speaker outputs of the digital surround
sound amplifier as shown above, you must now configure the amplifier's bass management
as follows:
Front: large
Subwoofer: no
Centre, rear: large /small (depending on size)
Connection variant no. 1
(Differences of models cause a different position of the operating elements.)
OFF AUTO ON
POWER
1
POWER
ON
OFF
+ RIGHT -
- LEFT +
- + - +
+ RIGHT -
- LEFT +
B
A
POWERPHASE
LOW LEVEL
INPUT
L
R
STANDBY
OFF
ON
0∞
180∞
R LRL
-
+
+
-
HIGH LEVEL
OUTPUT
HIGH LEVEL
INPUT
-3
3
d
2-14
FREQUENCYVOLUME
150
0 dB
-7
50
100 Hz
65
80
120
135
SUBWOOFER
LOUDSPEAKER
AMPLIFIER
LOUDSPEAKER
BDA Subwoofer 11.2006.indd 6-7 16.11.2006 13:28:00 Uhr
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadral algemeen at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadral algemeen in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 2,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info