Manual Qlima PGP113 (page 5 of 104) (English, Dutch, French, Italian, Spanish, Norwegian)

689391

Zoom out

Zoom in

1/104

PICTURES

Front

Back

ASSEMBLY PROCEDURES

Hardware Used

1. Assemble the wheel assembly to the

bottom plate. Fix the wheel assembly to the

bottom plate using 4pcs bolt M6X12 and 4pcs

flange nut M6.

x 4

Wrench

x 1

Bolt M6 X 12

M6 Flange nut

Hardware Used

2-1. Unscrew the switch button, load small

battery, tighten the switch button.

2-2. Insert the pins of the base to the holes of

lower support, press to secure the pins. Using

4pcs screw M5X12 to secure the lower support

and base.

Insert the pins of the control box assy to the

holes of upper support, press to secure the

pins. Using 4pcs screw 3/16” screw to secure

the upper support and control box assy.

x 4

Philips

screwdriver

x 1

Screw M5 X 12

x 4

3/16” Screw

AA Battery (1.5 V)

ASSEMBLY PROCEDURES

Hardware Used

1. Assemble the wheel assembly to the

bottom plate. Fix the wheel assembly to the

bottom plate using 4pcs bolt M6X12 and 4pcs

flange nut M6.

x 4

Wrench

x 1

Bolt M6 X 12

M6 Flange nut

Hardware Used

2-1. Unscrew the switch button, load small

battery, tighten the switch button.

2-2. Insert the pins of the base to the holes of

lower support, press to secure the pins. Using

4pcs screw M5X12 to secure the lower support

and base.

Insert the pins of the control box assy to the

holes of upper support, press to secure the

pins. Using 4pcs screw 3/16” screw to secure

the upper support and control box assy.

x 4

Philips

screwdriver

x 1

Screw M5 X 12

x 4

3/16” Screw

AA Battery (1.5 V)

Hardware Used

3. Assemble block belt.

Fix the block belt to the 2pcs of lower support

behind the front door, using 2pcs screw M5X12.

4. Assemble the middle support.

Insert the 4pcs upper support to the lower

support. Secure them with 8pcs screw 3/16”.

x 1

Philips

screwdriver

x 8

x 1

Philips

screwdriver

3/16” Screw

x 2

Screw M5 X 12

Hardware Used

3. Assemble block belt.

Fix the block belt to the 2pcs of lower support

behind the front door, using 2pcs screw M5X12.

4. Assemble the middle support.

Insert the 4pcs upper support to the lower

support. Secure them with 8pcs screw 3/16”.

x 1

Philips

screwdriver

x 8

x 1

Philips

screwdriver

3/16” Screw

x 2

Screw M5 X 12

Hardware Used

5. Assebmle the flame screen to the upper

support.

Secure the flame screen to the upper support

using 8pcs screw 3/16”.

6. Assemble the reflector onto the flame

screen.

Screw the 3pcs stud on the flame screen,

put 3pcs washer Φ6 onto the top of stud,

then put the reflector onto the stud, secure

them with 3pcs washer Φ6 and 3pcs wing

nut.

x 3

x 6

Hardware Used

x 8

Philips

screwdriver

3/16” Screw

x 1

Wing nut

Washer Φ6

Stud

Hardware Used

5. Assebmle the flame screen to the upper

support.

Secure the flame screen to the upper support

using 8pcs screw 3/16”.

6. Assemble the reflector onto the flame

screen.

Screw the 3pcs stud on the flame screen,

put 3pcs washer Φ6 onto the top of stud,

then put the reflector onto the stud, secure

them with 3pcs washer Φ6 and 3pcs wing

nut.

x 3

x 6

Hardware Used

x 8

Philips

screwdriver

3/16” Screw

x 1

Wing nut

Washer Φ6

Stud

7. Carefully install the glass tube by lifting up

and inserting through the center hole in the

upper plate. Ensure the black silicone ring is

attached to the lower edge of the glass tube

as illustrated. Slide the glass tube through the

hole of the lower plate cover and onto the

middle plate. Check and ensure that the glass

tube is positioned properly and is completely

covering the center hole of the middle plate.

8. Assembly the protective guard.

Hang the hooks of the protective guard onto

the holes in supports.

Secure the protective guards with fixing

brackets with 4pcs 3/16" screws.

To aid in installation

place black silicone

ring on the middle

plate and then

install glass tube.

Ensure the rim of

the glass tube sits

firmly in the black

silicone ring.

WARNING! The black

silicone ring must be in place

prior to operating the heater.

BLACK SILICONE

RING

Hardware Used

x 4

Philips

screwdriver

3/16” Screw

x 1

Fixing

Bracket

x 4

7. Carefully install the glass tube by lifting up

and inserting through the center hole in the

upper plate. Ensure the black silicone ring is

attached to the lower edge of the glass tube

as illustrated. Slide the glass tube through the

hole of the lower plate cover and onto the

middle plate. Check and ensure that the glass

tube is positioned properly and is completely

covering the center hole of the middle plate.

8. Assembly the protective guard.

Hang the hooks of the protective guard onto

the holes in supports.

Secure the protective guards with fixing

brackets with 4pcs 3/16" screws.

To aid in installation

place black silicone

ring on the middle

plate and then

install glass tube.

Ensure the rim of

the glass tube sits

firmly in the black

silicone ring.

WARNING! The black

silicone ring must be in place

prior to operating the heater.

BLACK SILICONE

RING

Hardware Used

x 4

Philips

screwdriver

3/16” Screw

x 1

Fixing

Bracket

x 4

9. Attach the three side panels to the heater

using 18pcs screw 3/16”.

Note : Do not cover the front side where

the control knob is.

Hardware Used

x 18

Philips

screwdriver

3/16” Screw

x 1

10. Install the knob to M4X6 screw. Hang the

chain to the hole on the control box assy and

put the pothook of front panel to the holes of

bottom plate.

Hardware Used

x 1

Knob

x 1

Philips

screwdriver

Screw M4 X 6

x 1

Chain

1 1a

3 4 5

6 7 8

9 10 11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Qlima PGP113 in the language / languages: English, Dutch, French, Italian, Spanish, Norwegian as an attachment in your email.

The manual is 5,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Qlima PGP113 Manual

Product: