600500

Qazqa 44964 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
INSTRUCTION MANUAL
These instructions are for your safety. Please read through them thoroughly prior to installation and
retain them for future reference.
Warnings
This product is Class I and must be earthed.
It is recommended that this fitting is installed by a qualified electrician.
This fitting should be fitted in accordance with IEE Regulations and the Building Regulations.
For you safety, switch off at the mains supply before installing or maintaining this fitting. Ensure
other persons cannot restore the electricity supply without you acknowledgement.
If you are in any doubt, please consult a qualified electrician.
If replacing an existing fitting, make a note of the connections.
Always use the correct type and wattage bulb. Never exceed the wattage stated.
When changing a bulb, always switch off at the mains and allow the old bulb to cool down before
handling. Dispose of used bulbs carefully.
The bulb and surrounding parts can become extremely hot during use.
Cable Type - The correct cable must be used for wiring this fitting. We suggest that you use
H05RN-F specification cable (not supplied) which is an outdoor grade, rubber sheathed cable.
Running it inside a plastic conduit (not supplied) should further protect it. Alternatively, if the cable is
to be in an area where it could become damaged, you should use special armoured cable. This type
of cable has a sheath that is strengthened to protect against damage from objects such as garden
tools, lawnmowers etc. The cable must have a minimum cross sectional area of 1.0mm² and
wherever possible, cables should be run horizontally. Bury the cable minimum of 50cm.
A light fitting should be connected to a lighting circuit protected by a 5-amp fuse, (or 6-amp residual
current device). If a light fitting is to be connected to a ring main, a fused connection unit fitted with a
3-amp fuse should be installed. This product is only suitable for connection to AC 220-240V / 50Hz
supply.
We always recommend the use of an approved RCD unit.
Replace any cracked/damaged diffuser immediately-do not use if they are damaged.
The fitting is suitable to be installed in normally non-accessible areas. The product cannot be
mounted in areas where motor vehicles may circulate, carriageways, parking areas.
The product has a rated maximum surface temperature of 160 ºC.
Dangerous voltage! To indicate hazards arising from dangerous voltages.
We recommend only using the lamp that is with ultraviolet ray filter.
Specifications
Product type: 44964
Rated voltage: AC 220-240V, 50Hz
Source of light: 70W, G12 (included)
Degree of protection: IP67 ＆ IP65
Protection class: I
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Qazqa 44964 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Qazqa 44964 in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info