572632

Pulsar Forward DN55 Manual

6
Zoom out
Zoom in
Previous page
1/8
Next page
10
11
MAIN MENU
SumLight™
After the digital module is switched on for the first time, the Sum Light™
activates automatically. The use of Sum Light™ substantially increases
sensitivity of the CCD array thus enabling observation in low light without
using the IR Illuminator.
When using the digital module at a sufficient level of night illumination, the
Sum Light™ function can be deactivated manually (using the wireless RC or
the menu). Hereafter on activation the module remembers the function status
before it was turned off.
NOTE: higher sensitivity causes an increased noise level in the picture,
lower frame rate; image slows down, if the unit is rapidly moved from
one side to the other, the picture may be blurred for a moment. Neither of
these effects is a flaw of the unit. After the SumLight™ Signal
Processing Program is activated, light dots (pixels) may appear in the
field of view which is explained by operation peculiarities of this
function. This is not a defect either.
• Keep the encoder (5) pressed for two seconds - submenu M1 appears on
the display.
• Rotate the encoder to choose the icon and it will show up on the data
panel.
The menu includes two submenus and which include items as
follows:
- function “Sum Light™”
- function “Autocontrast”
- return to default
settings
- function “Clock”
- v ideo output selection
- function “Horizon adjustment”
- wireless remote control
The active submenu is highlighted with a frame
To switch to the other submenu, rotate the encoder and move the cursor
to or (the frame will be flashing) and push the encoder.
Autocontrast mode
• Keep the encoder (5) pressed for two seconds - submenu M1 appears on
the display.
Rotate the encoder to choose icon .
• Push the encoder “On” and “Off” signs will show up next to the
icon . Select “On” and press the encoder to activate the function.
• To deactivate select “Off”.
Push the encoder - “On” and “Off” signs will show up next to the
icon . Select “On” and press the encoder to activate the function.
• To deactivate select “Off”.
• To exit main menu, hold the encoder (5) pressed for two seconds. Or wait
ten seconds to exit automatically.
Clock
Please do the steps as follow to setup the clock:
• Keep the encoder pressed for two seconds and rotate to choose icon
in submenu M2.
• Push the encoder and rotate it to select time format . 24/PM/AM
Parameter being changed blinks.
• Push the encoder to pass to the hour setup.
Rotate the encoder to setup hour.
• Push the encoder to pass to the minute setup.
Rotate the encoder to setup minute.
• To exit the “Clock” item, keep the encoder (5) pressed for two seconds.
Video output selection
• Keep the encoder pressed for two seconds and rotate to choose icon
in submenu M2.
• Push the encoder and rotate to select video output standard –
PAL or NTSC.
• Push the encoder again to confirm.
• To exit main menu, keep the encoder (5) pressed for two seconds.
Or wait ten seconds to exit automatically.
Horizon adjustment function
Horizon adjustment function is designed to align the digital module
horizontally relative to the reticle of your day device.
• Rotate the encoder (5) to choose icon .
• Push the encoder: vertical arrows will appear next to and a
horizontal and a vertical line will appear on the display.
• Rotate the encoder to move the horizontal line upwards/downwards so
that it matches the horizontal bars of your day devices’s reticle. Vertical
bars of the reticle should match the vertical line.
Enter the menu by keeping the encoder (5) pressed for two seconds.
Rotate the encoder (5) to choose the icon in submenu M1 and push
the encoder – the following settings will be restored to default values:
- SumLight - On; Autocontrast - Off; Brightness - 10; Contrast - 10.
Restore default settings
If the lines do not match, release the clamp and re-mount the digital
module to ensure its horizontal position .
Check that the lines match, snap the clamp and tighten the screw.
Wireless remote control
The wireless remote control duplicates activation of the scope, IR Illuminator
and Sum Light™ mode.
The unit has three buttons:
• “ON” button (14) – turning on/off the unit (keep pressed for two
seconds to turn on the unit);
• “IR” button (15) - turning on/off the IR Illuminator, powers settings
selection;
• “Sum Light™” button (16) – activation/deactivation of “Sum Light™”
function.
When finished, turn off the device by pushing the “ON” button (7).
Close the lens cap (1).
To exit main menu, keep the encoder (5) pressed for two seconds.
Or wait ten seconds to exit automatically.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pulsar Forward DN55 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pulsar Forward DN55 in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info