Manual Pulsar Edge GS2 (page 4 of 14) (English, German, French, Italian, Spanish)

572623

Zoom out

Zoom in

1/14

Make sure that the batteries have been installed according to the instructions

found in the battery installation section of this manual.

USE AND TESTING

Enter a dark area before turning on the binocular.

Remove the objective caps.

Activate the device by pushing the “ON” (2) button. The green LED indicator (3)

lights up. If the batteries are low, the colour of the indicator will turn red.

You can test your binocular in a light area without removing the protective caps.

This will not damage your unit.

If the subject to be viewed is in a completely dark area, including lowlight

shadow areas; activate the infrared illuminator (4) by pushing the “IR” button

(5). To adjust the IR power, rotate the controller (6).

Direct the turned on binocular at an object at a distance of about 10-100

meters. Rotating the eyepieces (7), focus on the tube's screen - rough surface

or tiny dark dots are visible. Rotate the objective lenses (1) until the image

quality is optimal. Re-focus the eyepieces, if necessary. After this adjustment

you may not rotate the eyepieces irrespective of the distance and objective

lenses.

Point the binocular at an object to be viewed and adjust the final focus by

rotating the objective lens focusing ring until the image is optimal. When

screwing the objective lenses into the housing, it focuses on farther objects,

when screwing out - on closer ones.

When you are finished using your binocular place the caps back onto the

objective lenses and turn off the unit by pushing the “ON” (2) button, the LED

indicator will go out. Put the binocular into the carrying case.

CAUTION!

Your device can be used in extreme cold. However, when the unit is brought

back into a warm environment, you must wait approximately 2-3 hours before

using the unit again. Failure to do so may result in damage as a result of

condensation accumulating on the internal circuitry of the unit.

TROUBLESHOOTING

The scope will not turn on.

Check that the batteries are installed properly. Install the batteries according to

the (+) and (-) polarity, ensuring that the markings on the battery and battery

compartment correspond with one another. Check the battery contacts to

ensure they are clean and free of corrosion; if necessary, clean the contacts

with rubbing alcohol. Also check that the cap of the battery department is fully

closed, otherwise the device will not operate. If necessary, replace the

batteries as they may be depleted. Also be sure that the “ON” button has been

pushed and the green LED is on.

Distinct black dots appear on the screen.

These dots are cosmetic blemishes resulting from tube production processes

and do not interfere with the reliability or performance of the scope and are not

a defect.

The image “snows”.

Image may “snow” in a dark environment during 30-60 seconds after the

device is activated; this effect disappears soon. Image may slightly “snow” if

the device was previously operated without the lens caps at a high level of

luminance. Image may also “snow” if the device is operated in complete

darkness with the IR illuminator off.

The image is not focused.

Adjust the focus of the eyepieces and the objectives (see “Use and Testing”

section). Check that the lenses are not foggy or dusty; if they are, carefully

clean the external surfaces of lenses with a soft cotton fabric. Replace the

batteries if the total battery charge is less than 2.2V.

When the unit is brought into a warm environment from a cold one,

condensation may appear on the internal lenses; you must wait two hours

before using the unit.

Visibility decreases or disappears.

Turn the power off and turn the binocular away from the light source; visibility

will restore itself immediately.

During long-time storage please remove the batteries to prevent possible

leakage. The battery cover must be fully screwed during long-time storage.

STORAGE

Clean the lens with professional lens cleaning supplies intended for use with

multicoated optics.

Blow any dust or dirt off the lenses using dry, compressed air.

Clean the unit housing with a soft, clean cloth.

MAINTENANCE

Match the boss of the battery compartment with the groove of the battery cover.

The cover should tightly fit the body along the perimeter, avoid skewing. Lock the

cover by turning the screw of the battery cover 90° counterclockwise.

OPEN

5 6

2 3

90º

4 1

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Pulsar Edge GS2 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Pulsar Edge GS2 Manual

Product: