490713

Protool PLP 350 E Manual

9
Zoom out
Zoom in
Previous page
1/68
Next page
Cutting blades
Operating the electric tool for
a first time
Remaining risks
Lateral guide roller
9
GB
9. Keep hands away from the chip discharge
channel. If the channel is blocked, first the electric
tool must be switched off and allowed to come to a
complete standstill. After that, the chips may be
removed.
10. Secure work in a safe position with enough support
for a workpiece and the electric tool.
11. Whenever possible, the electric tool should be
connected to the mains via a fault current circuit
breaker (Fl) or a PRCD safety device.
12. This electric tool is not intended for stationary use.
13. The dust originating from planing wood is
hazardous to health. Connect the dust extraction
adapter and wear a dust mask when working with
the electric planer.
14. Turn or exchange blunt knives in good time, the
risk of kickback is otherwise increased.
15. After planing is finished, only put the planer aside
after the cutting head has come to a complete
standstill.
16. Damaged power supply cords must be replaced
immediately by a specialist.
17. Unauthorized use of this product anyway may lead
to a personal injury.
18. Repairs shall be carried out by the qualified
personnel only.
19. Use only the original spare parts.
20. Use safety glasses and ear protection.
21. Use only the original cutting heads identical to the
one supplied with the electric tool.
Even when the electric tool is used properly and all the
relevant safety measures are followed, the following
remaining risks can still occur due to the design of the
electric tool required for the intended working
operations:
- contact with the cutting blades during rundown;
- clothing can be caught by the rotating parts;
- hazards invited by the flexible supply cord;
- hazards invited by the harmful dust when using the
planer for a long time without a dust extractor.
- Check if the data on the nameplate correspond with
the actual voltage of the power supply. The electric
tools with rated voltage 230 V may be also
connected to 220 V. Fusing for 230 V: 16 A slow-
action fuse or equivalent automatic circuit breaker.
- The planer is equipped with the overload cut-out and
LED overload indicator. The overload cut-out
protects the motor against excessive overloading.
- Use only extension cords with a cross section of
3 x 2,5 mm , max. 50 m length. When the electric
tool is used outdoors, use only extension cords
intended for outdoor use and so marked.
- Connection to a standby unit or generator: minimum
power 5 kVA / 230 V, 50 Hz.
2
- There must be no metal particles on the surface of
the workpiece to be planed. For secure guidance,
the planer is equipped with three handles. Planing
depth is adjustable by means of the swiveling front
handle (5) and the value of adjusted planing depth
may be read on the scale (6) on the side wall of the
planer.
- Attach the supplied chip deflector (12) in front of the
planer on the chip discharge channel (11) and fasten
it with the two star-shaped fixing knobs (13).
- The incorporated soft-start/brake electronic circuit
“SSB electronic” provides for soft starting when the
electric tool is switched on, as well as short rundown
time of approx. 5 s when the electric tool is switched
off.
- When working with the planer, place the front
adjustable shoe (7) onto the workpiece and switch
the motor on, using the switch (2) with the lock-off
button (4) depressed simultaneously. As soon as the
cutting head comes in contact with the workpiece,
guide the planer with constant feed speed, applying
light pressure.
- When planing for a long time with the maximum
planing depth 2,5 mm adjusted and maximum
planing width 350 mm utilized, the LED overload
indicator (24) is to be observed to make sure that the
electric tool is not overloaded - the LED light
intensity increases with overload and the cut-out is
triggered after certain overload rate is achieved. The
electric tool can be started again only after the mains
switch (2) has been released and pressed again.
When intense chip generation is anticipated, there is
advisable to work without the chip deflector (12)
attached.
- In closed rooms, this electric tool may only be
operated with a dust extraction device connected.
When the maximum planing width of 350 mm is to be
utilized, there is possible to use the included guide
roller (9) which rests on the base plate right to the
switch; if required, the guide roller may pulled off with a
light jerk and inserted into the bore on the left side of
the base plate of the planer. When the job is finished,
pull the roller from its operating position and put it back
to the fixture on the base plate.
The cutting head (15) is fitted with the pair of special
reversible blades (16) which cannot be resharpened but
may be reversed once. Blunt blades reduce quality of
the work and increase the risk of kickback. Therefore
they must be turned or replaced in good time.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool PLP 350 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool PLP 350 E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info