460045
3
Zoom out
Zoom in
Previous page
1/8
Next page
THE APPLIANCES ARE NOT FOR CHILDREN UNDER 14 YEARS OF AGES.
THE PEDAL CRANK TRAINING EQUIPMENT OF CLASS B AND C IS NOT
SUITABLE FOR THERAPEUTIC PURPOSES.
REPLACED DEFECTIVE COMPONENTS IMMEDIATELY AND KEEP THE
EQUIPMENT OUT OF USE UNTIL REPAIR .
THE MOST SUSCEPTIBLE TO WEAR PARTS ARE
DRUM MAGNETIC WHEEL
MOTOR
BELT
STEP 1. FIT FRONT STABILIZER ( 2 ) TO THE FRAME ( 1 ) WITH CARRIAGE BOLTS ( 27 ) &
WASHERS ( 29 ) & NUTS ( 33 ), NOTE TO PREVENT HEAD OF CARRIAGE BOLTS ( 27 )
FROM DAMAGING FLOOR, DIMPLED SQUARE HOLES ON STABILIZER ( 2 ) MUST BE
FACING DOWN. ATTACH REAR STABILIZERS ( 3 ) TO REAR SIDE OF MAIN FRAME
( 1 ). FASTEN WITH BOLTS ( 28 ) WASHERS ( 29 ).
STEP 2.
a. ATTACH PEDALS ( 18 / 19 ) TO PEDAL CRANKS, ( PEDALS MARKED "L" AND "R"
INDICATES LEFT AND RIGHT SIDE OF BIKE. MAKE SURE NOT TO MIX IT UP ).
b. LEFT PEDAL HAS LEFT-HAND THREAD AND MUST BE TURNED
COUNTERCLOCKWISE ( CCW ) TO ATTACH, RIGHT PEDAL HAS RIGHT-HAND
THREAD, MUST BE TURNED CLOCKWISE ( CW ) TO ATTACH.
STEP 3. ATTACH SADDLE ( 20 ) TO SADDLE PLATE OF SEAT POST ( 04 ). FASTEN IT WITH
SPRING WASHERS ( 31 ) AND NYLON NUTS ( 32 ).
SLIDE SEAT POST ( 04 ) TO SEAT POST BOOT ( 21 ), THEN ATTACH TO MAIN FRAME
( 01 ). ADJUST THE HEIGHT OF THE SEAT BY THE KNOB ( 26 ). TIGHTENED THE
KNOB FIRMLY AFTER ADJUSTMENT.
STEP 4. CONNECT MONITOR CABLE A ( 9, FROM END OF #5 HANDLEBAR POST ) AND
MONITOR CABLE B ( 10, FROM MAIN FRAME ), THEN FIT HANDLEBAR POST ( 5 ) TO
MAIN FRAME WITH BOLTS ( 28 ) AND WASHERS ( 29 ),
STEP 5. ASSEMBLE HANDLE BAR ( 06 ) ONTO HANDLE BAR POST ( 05 ), FIX WITH WASHERS
( 29 ) AND BOLTS ( 28 ),
STEP 7. CONNECT MONITOR CABLE A ( 9, TOP OF HANDLEBAR POST ) TO THE MONITOR
( 08 ), THEN ATTACH MONITOR ( 08 ) TO THE MONITOR MOUNTING PLATE ( AT TOP
OF HANDLEBAR POST ) WITH SCREWS ( 22 )..
NOW THE ASSEMBLY OF THE PROGRAMMABLE MAGNETIC CYCLE IS DONE,
PLEASE NOTE WITH THE FOLLOWING INFORMATION BEFORE USE, THE MACHINE
IS REQUESTED TO USE AC ADAPTER, WHICH SHOULD BE WITH OUTPUT 9V / 1000
MA, PLEASE ALSO REFER TO MONITOR INSTRUCTION FOR THE PROPER
SPECIFICATION INFORMATION.
BEFORE YOU BEGIN
IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY. ASSEMBLE THE UNIT IN ACCORDANCE
WITH THE STEPS IN THE MANUAL. LAY OUT ALL PARTS ON THE FLOOR AND
CHECK IF YOU HAVE ALL THE PARTS INCLUDED COMPLETELY BEFORE
BEGINNING ASSEMBLY. IN CASE OF A DISCREPANCY, PLEASE CALL THE
CUSTOMER SERVICE DEPARTMENT OF THE STORE FOR HELP.
NOTE: SOME PARTS MAY BE FACTORY PRE-ASSEMBLED.
TOOLS REQUIRED FOR ASSEMBLY
ONE ADJUSTABLE WRENCH, A PHILIPS HEAD SCREWDRIVER AND A ALLEN KEY
ASSEMBLY
- 2 -
IMPORTANT : READ ALL STEPS BEFORE ATTACHING PEDALS
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Proteus PEC-4650montage at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Proteus PEC-4650montage in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Proteus PEC-4650montage

Proteus PEC-4650montage User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info