566798

Profile PIN-136 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
3-in-1 DIGITAL DETECTOR EN - 1
PIN-136
We thank you for the purchase of this Profile product.
Please note: It is important that you read this manual
before using the product And be sure to save this
manual for possible use later.
Features and advantages
1. foot for vertical fixing
2. Spirit level
3. Feet for horizontal fixing
4. foot for spirit level
5. Function key metal
6. Function key laser
7. Function key wood
8. on-key
9. LCD display
10. Adjusting ring laser angle
Features and advantages
Detection of wood/metal and live 230V wires –
detects to a depth of maximum 3/4" (19 mm)
Signals obstacles with a noise and displays this on the
LCD display. 180” adjustable laser with spirit level
and perpendicular line glass
LCD display with graphic display
LED light for continuous detection of live wires
Laser line projection 6.5 metres
With adjustable legs for bringing the laser level
Vertical and horizontal fixing feet
Simple key operation
Ergonomic designed to enhance comfort and grip
Automatic switching off
Low battery capacity indication
Safety instructions
If the warnings are not heeded this can result in
physical injury.
Heed the following warnings to prevent physical
injury:
• Never remove the warning labels.
• Do not point the laser beam directly at other people's
eyes.
• NEVER look directly into the laser beam.
• Do NOT point the laser beam at a reflective surface.
• Do NOT use near children and do not allow use by
children.
• Never disassemble the laser.
Always switch the laser off when the appliance is not
in use.
Introduction
The unit uses electronic signals to locate the position of
wooden beams, connections or live AC wires under
plasterwork and
other common wall materials. When the edge of the
beam/plank is detected the unit's LCD display gives a
visual and acoustic signal to enable you to
exactly determine the edge of the beam. You can mark
the place of the beam edges with a pencil line. The unit
generates a vertical laser plane and turns 45 or 90
degrees to the right or to the left to generate a straight
laser line.
Operating instructions
Detection mode is selected with the function keys - metal
or wood.
The standard mode is the detection of wooden beams.
The preferred mode must be selected before "on" is
pressed.
Calibration
Calibrate the unit on a wall before you scan for wooden
or metal elements or power lines.
Please note! The calibration of the unit must take place
on a wall in which you know there are no wooden/metal
or electrical parts. Still wet or just painted surfaces can
also affect the good calibration of the unit. If you
do not adhere to the points mentioned above, the unit
will not give the correct location of concealed objects in
walls and ceilings.
Different surfaces
Wallpaper: there is no difference in the operation of the
sensor with surfaces hung with wallpaper or textiles
unless this wallpaper contains metallic foil or fibres.
Plasterwork or lath walls: the unit will function
correctly unless the plasterwork or laths are
exceptionally thick or contain metal meshing.
Ceilings or surfaces with a textured finish: when a
rough surface has to be scanned, such as a sprayed
textured ceiling, you can use a piece of cardboard to
scan the surface. Carry out the abovementioned
calibration WITH the piece of cardboard between the
sensor and the surface.
Detection of wooden beams
When the unit is switched on, as default it is in the
detection mode for wooden beams.
1. Slide the unit in a straight line over the surface. As
the unit comes closer to the beam, more lines will
be seen as shown in picture 2. When the edge of
the beam is detected, the wood indication and the
edge line will be seen as in figure 3. The unit
sounds a repeated beeping.
2. Use the indication line to mark the edge of the
beam.
3. Slide further over the beam. When the indication
goes out and the unit stops beeping the other edge
has been detected.
4. Carry out an extra check of the location of the beam
by approaching it from the other side.
5. The middle point between the markings indicates
the middle of the beam.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Profile PIN-136 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Profile PIN-136 in the language / languages: English as an attachment in your email.

The manual is 0,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Profile PIN-136

Profile PIN-136 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info