566794

Profile PIN-112 Manual

1
Zoom out
Zoom in
Previous page
1/3
Next page
MULTIMETER MEDIUM EN - 1
PIN-112
We thank you for the purchase of this Profile
product. Note: It is important that you read this
manual before using the product. Save this manual
for possible use later.
Operating controls and connections
(See figure)
1. LCD
2. Function switch
3. COM (negative) input connection
4. 10A (positive) input connection for 10A DC or
AC measurement
5. Positive input connection
6. HOLD push button
7. Background lighting
Symbols and messages
Continuity
BAT Battery nearly empty
Diode
V
~ AC voltage
V DC voltage
A Direct current
μ Micro (Ampere)
m Milli (Ampere)
k Kilo (Ampere)
Ω Ohm
Danger live voltage
Consult the manual
Safety class II, Double insulated
Operation
Warning: Risk of electrocution. Circuits with high
voltages (both direct and alternating) are very
dangerous and must be very carefully measured.
1. ALWAYS switch the function switch to the OFF
position when the meter is not being used.
2. When "1" appears on the display during a
measurement the value exceeds the range you
have selected. Choose a higher range.
Opm.: With some low AC and DC ranges the
display may show a random, varying measured
value although the testing wires are not connected
to an appliance. This is normal and caused by the
high input sensitivity. The measured value will
stabilise and a correct measurement will be shown
on connection to a circuit.
Display background lighting
Briefly press the backlight key (7). The lighting will
be automatically switched off after 10 seconds.
Hold
With the Hold function you can hold the current
value on the display. Press the HOLD key (6) briefly
to hold the value and press HOLD again briefly to
close the function.
DC voltage measurements
Caution! Do not measure DC voltages when a
motor in the circuit is switched ON or OFF. This can
cause large voltage peaks that could damage the
meter.
1. Switch the function switch to the V position.
Insert the banana plug of the black testing wire in
the negative (3)COM connection and the plug of the
red wire in the positive (5) connection
2. Choose a value 1 step higher than the expected
measurement.
3. Touch the circuit to be tested with the test probes.
Ensure correct polarity (red wire to positive, black
wire to negative).
4. Read off the voltage on the display. The display
will show the correct decimals and value. When the
polarity is reversed the display will show (-) minus
for the value.
AC voltage measurements
Caution! Do not measure AC voltages when a
motor in the circuit is switched ON or OFF. This can
cause large voltage peaks that could damage the
meter.
1. Switch the function switch to the V position.
2. Choose a value 1 step higher than the expected
measurement.
3. Insert the banana plug of the black testing wire in
the negative (3)COM connection and the plug of the
red wire in the positive (5) connection.
4. Touch the circuit to be tested with the test probes.
Read off the voltage on the display. The display will
show the correct decimals, value and symbol.
Resistance measurements
Warning! To prevent electric shocks one must cut
the power supply to the unit to be tested and
discharge all capacitors before resistance
measurements are conducted. Remove the
batteries and take the plugs out of the plug socket.
1. Switch the function switch to the 2000k Ω
position.
2. Insert the banana plug of the black testing wire in
the negative (3)COM connection and the banana
plug of the red testing wire in the (5) positive
connection.
3. Touch the circuit or part to be tested with the test
probe tips. It is best to disconnect a side of the part
to be tested so the rest of the circuit does not
interfere with the resistance measurement.
4. Read off the resistance on the display. The
display will show the correct decimals, value and
symbol. Lower the position if necessary until the
correct resolution is achieved.
1


Need help? Post your question in this forum.

Forumrules
1

Forum

profile-pin-112

Reset search

  • Bonjour Comment changer les piles sur un Multimètre Numérique Profile PIN-112 ? Submitted on 2-11-2021 at 13:34

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Profile PIN-112 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Profile PIN-112 in the language / languages: English as an attachment in your email.

The manual is 0,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Profile PIN-112

Profile PIN-112 User Manual - Dutch - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info