566791

Profile PIN-100 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
MULTIMETER POCKET EN - 1
PIN-100
We thank you for the purchase of this Profile product.
Note: It is important that you read this manual carefully
before using the product and be sure to save this
manual for possible use later.
Symbols and messages
V
~ ACV - AC voltage
V DCV - DC voltage
A DCA - Direct current
μ Micro (Ampere)
m Milli (Ampere)
k Kilo (Ampere)
Ω Ohm
Danger live voltage
Consult the manual
Safety class II, Double insulated
Cat II Overvoltage class II
Safety measures
1. Incorrect or inappropriate use of this meter can
cause damage, electric shocks or serious or fatal
injury. Make sure that you have read and
understood this user's manual before you use the
meter.
2. Make sure that all covers and the battery cover are
closed and firmly tightened.
3. Always disconnect the testing wires from the power
source before replacing the battery or fusing.
4. Never exceed the maximum nominal input values.
5. Be very careful with measurements when the
voltages are higher than 25V AC or 35V DC. At
these voltages one must be aware of the risk of
electric shock.
6. Always discharge the capacitors and remove power
from the appliance that must be tested before you
carry out diode, resistance or continuity tests.
7. Remove the battery from the meter when the meter
is not to be used for a longer period.
Voltage measurement AC/DC
Caution! Do not measure AC/DC voltages when a motor
in the circuit is switched ON or OFF. This can cause large
voltage peaks that could damage the meter. Do not
measure voltages on sockets & engines.
1. Switch the function switch to the DCV or ACV
position.
2. Touch the negative side of the circuit with the black
measuring pin. Touch the positive side of the circuit
with the red measuring pin.
3. Read off the voltage on the black meter scale.
Current measurement DC
Caution! Do not measure currents on sockets & engines.
1. Switch the function switch to the DCA position.
2. For current measurements to max. 250mA DC
switch the function switch to the mA position
3. Switch the voltage of the circuit to be tested off and
open the circuit at the point where you want to
measure the current intensity.
4. Touch the negative side of the circuit with the black
measuring pin. Touch the positive side of the circuit
with the red measuring pin.
5. Put power on the circuit.
6. Read off the current strength on the black meter
scale.
Resistance measurement
Warning! To prevent electric shocks one must cut the
power supply to the unit to be tested and discharge all
capacitors before resistance measurements are
conducted. Remove the batteries and take the plugs out
of the plug socket.
1. Switch the function switch to the Ohms position.
2. Hold the measuring pins with the ends together and
set the pointer using the black setting screw until
the pointer is on zero on the green scale.
3. Touch the circuit or part to be tested with the
measuring pins. It is best to disconnect a side of the
part to be tested so the rest of the circuit does not
interfere with the resistance measurement.
4. Read off the resistance on the green meter scale.
Battery test
1. Switch the function switch to BATTV and set the
voltage to 9V or 1.5V depending on the voltage of
the battery to be tested.
2. On the bottom red scale you can now read the
condition of the battery. “Bad“ means that the
battery is empty or nearly empty, “GOOD” means
the battery is full.
Replacing the battery
1. Remove the cover in the bottom (make sure you do
not lose the screw).
2. Replace the old battery by a new 1.5V AA battery.
3. Replace the cover in the bottom and tighten the
screw.
Specifications
Max. input voltage: 500V AC/DC
Meter scale: ± 5% variation on a
complete scale value of
DC/AC and Ohm range
Battery: 1 x 1.5V AA
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Profile PIN-100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Profile PIN-100 in the language / languages: English as an attachment in your email.

The manual is 0,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Profile PIN-100

Profile PIN-100 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info