566737
1
Zoom out
Zoom in
Previous page
1/2
Next page
ADAGIO SET – Cordless doorbel set UK - 1
PAC-312 / PAC-314 / PAC-316 / PAC-318
Thank you for purchasing this Profile product. Please
note: It is important that you read this manual before
using the product. And be sure to save this manual for
possible use later.
The cordless doorbell consists of 2 separate
components:
1. Push-button unit (transmitter)
2. Bell unit (receiver)
These items are completely independent of each other
and require no wiring.
When the push-button is pressed in, a signal is sent to
the bell, whereupon the bell is activated. Since it has a
range of up to 100 meters (in open spaces) you can use
the bell virtually anywhere in the house, workshop,
office, set it up in the garden or just carry it with you.
Battery installation
Push-button unit
1. The push-button unit works using 1 x 3v
(CR2032) lithium battery (included).
2. The lithium battery is already installed. Open
the push-button and remove the insulator
strip.
3. Snap the rear side back into position, and the
push-button is ready for use.
To replace the battery:
1. Open up the push-button unit.
2. Remove the metal plate using a screwdriver.
3. Place a 3v battery (CR2032) in the battery
compartment, making sure the positive
terminal (+) is uppermost.
Bell unit
1. Slide the rear cover open.
2. Place 2 AA alkaline batteries into the battery
compartment.
3. The bell unit will produce a two-tone signal,
indicating that it is ready to read a digital code
(see channel selection).
4. Slide the cover firmly back into place; the bell
is now ready for use.
Installation
Push-button unit
Use the two small holes on the
rear of the push-button to mark
the position for securing in
place. Drill small holes and
mount the push-button in
position with screws (self-
tapping 3 x 16mm, included) or
use the double-sided adhesive
tape (included).
Important: If you secure the
push-button onto a metal
upper surface or PVC type of
door (with metal), its maximum range of transmission
will be greatly reduced.
Bell unit
This bell can be used as a portable device - or fixed into
position. On the reverse side, there are two suspension
slots, with which the bell can be hung up using a screw,
and can easily be taken down again. Drill a small hole
and fix a rawlplug in place. Mount the hook (included)
onto the wall using a screw. The bell unit can hung up
safely in this way.
Choice of bell tone
The bell-tone selector button is inside the push-button
unit, below letter “S”. Press the button once to hear the
bell tone already set. Press again to hear and select the
next tune.
1. Long Westminster chime 2. Ding-Dong
3. Telephone ring 4. Circus theme
5. Banjo on my knee 6. Twinkle-twinkle
7. It’s a small world 8. Barking dog
Optionally: It is possible to install an extra push-button
by your back door. By applying the procedure given
above, each push-button can produce a different tune.
Channel selection
The unit is supplied with a pre-set radio frequency. If by
chance the bell should sound for no apparent reason,
it's possible that another device nearby is using the same
frequency. To get round this problem, you can change
the frequency of the push-button and bell.
1. remove the cover behind the push-button.
2. To program or change: remove the batteries
from the bell unit for at least 30 seconds to
prime the memory.
3. place the batteries back into position within.
Press the push-button after the two-tone signal
sound (with a second press of the button if
need be) to confirm the new code. Do this
within 1 minute. Don’t use any other cordless
products for the next 5 minutes.
4. Test for correct operation.
Volume selection
There is a volume-selector button inside the bell unit.
Slide the button to ‘high’ (85 dB) or ‘low’ (82 dB) to set
at the desired bell volume.
Trouble-shooting and tips
Problem: Bell rings, but LEDs fail to light up
Possible cause: - The bell is out-of-range (max.
100m in open spaces)
Possible solution: - Move the bell within range
- Reprogram the channel (see
channel selection)
Problem: Bell does not ring, nor do the LEDs
light up
Possible cause: - Push-button battery is flat
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Profile PAC-318 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Profile PAC-318 in the language / languages: English as an attachment in your email.

The manual is 0,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Profile PAC-318

Profile PAC-318 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info