566709
1
Zoom out
Zoom in
Previous page
1/2
Next page
PAVANE – Cordless doorbel set UK - 1
PAC-300
Thank you for purchasing this Profile product.
Please note: It is important that you read this
manual before using the product. And be sure
to save this manual for possible use later.
The cordless doorbell consists of 2 separate
components:
1. Push-button unit (transmitter)
2. Bell unit (receiver)
These items are completely independent of
each other and require no wiring.
When the push-button is pressed in, a signal is
sent to the bell, whereupon the bell is
activated.
Battery installation
Push-button unit
1. The push-button unit works using 1 x 3v
(CR2032) lithium battery (included).
2. The lithium battery is already installed.
Open the push-button and remove the
insulator strip.
3. Snap the rear side back into position, and
the push-button is ready for use.
To replace the battery:
1. Open up the push-button unit.
2. Remove the metal plate using a
screwdriver.
3. Place a 3v battery (CR2032) in the battery
compartment, making sure the positive
terminal (+) is uppermost.
Installation
Push-button unit
Use the two small holes on the rear of the
push-button to mark the position for securing in
place. Drill small holes and mount the push-
button in position with screws (self-tapping 3 x
16mm, included) or use the double-sided
adhesive tape (included).
Important: If you secure the push-button onto
a metal upper surface or PVC type of door
(with metal), its maximum range of
transmission will be greatly reduced.
Bell unit
1. A/C 230volt~50Hz
2. Stick the bell unit in a suitable plug, it is
ready for use immediately. (the green LED
light comes on)
3. Test the bell to make sure the gong is
within reach of the push button.
4. The plug can be used up to 230V, with a
maximum of 13A.
5. The bell has an autodidactic code-system.
Once connected, a 2 tone signal means it
is ready to learn a new code.
Choice of bell tone
The bell-tone selector button is inside the
push-button unit, below letter “S”. Press the
button once to hear the bell tone already set.
Press again to hear and select the next tune.
1. Long Westminster chime 2. Ding-Dong
3. Telephone ring 4. Circus
theme
5. Banjo on my knee 6. Twinkle-twinkle
7. It’s a small world 8. Barking dog
Optionally: It is possible to instal an extra
push-button by your back door. By applying the
procedure given above, each push-button can
produce a different tune.
Channel selection
The unit is supplied with a pre-set radio
frequency. If by chance the bell should sound
for no apparent reason, it's possible that
another device nearby is using the same
frequency. To get round this problem, you can
change the frequency of the push-button and
bell.
1. remove the cover behind the push-button.
2. To program or change: remove the
batteries from the bell unit for at least 30
seconds to prime the memory.
3. place the batteries back into position
within. Press the push-button after the two-
tone signal sound (with a second press of
the button if need be) to confirm the new
code. Do this within 1 minute. Don’t use
any other cordless products for the next 5
minutes.
4. Test for correct operation.
Volume selection
There is a volume-selector button inside the
bell unit to set at the desired bell volume.
Trouble-shooting and tips
Problem: Bell rings, but LEDs
fail to light up
Possible cause:- The bell is out-of-range
(max. 80m in open spaces)
Possible solution: - Move the bell within
range
- Reprogram the channel
(see channel selection)
Problem: Bell does not ring, nor do the
LEDs light up
Possible cause:- Push-button battery is flat
- Batteries are not correctly
installed in the push-button
Possible solution: - Replace battery
- Reinstall the batteries in their
correct positions (see battery
installation for push-button
unit)
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Profile PAC-300 Pavane at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Profile PAC-300 Pavane in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Profile PAC-300 Pavane

Profile PAC-300 Pavane User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info