685327

PowerTech Marine Power System Manual

4
Zoom out
Zoom in
Previous page
1/7
Next page
Depending upon the location of your Marine Power System; either above or below the water
line, some additional components may be required to complete the installation. See the following pages
for details on each system.
Cooling Water Supply Through-Hull Seacock Fitting (Flush Hull Type)
Shut OFF Valve
Seawater Strainer
Fuel System Primary Filter / Water Separator
Shut OFF Valve
Exhaust System Siphon Break
Hydro-Muffler
Zinc Anode
Shut OFF Valve or Cover
AC/DC Electrical Systems
Ship to Shore Transfer Switch
Remote Gauge Panel
INSPECTION of EQUIPMENT:
Prior to accepting your Marine Power System, check the unit for any shipping damage and be
sure all accessories ordered are present. Check the contents against the packing list and report any loss
or damage to the transportation company.
RIGGING and LIFTING:
Because of the size and weight of the unit, careful planning for rigging and lifting must be
considered. Each unit is equipped with lifting eyes that are designed to carry the full weight of the
generator. These lifting eyes are located on the upper engine section of the unit and allow the unit to be
hoisted horizontally. In some situations the hatchway may not be large enough to accommodate the unit
in the horizontal position. Therefore hoisting the unit in a vertical position will be necessary and
specialized rigging may be needed to accomplish vertical hoisting. Be especially careful that the rigging
does not interfere with or damage components on the unit. Never attach rigging to components or
accessories, remove these parts if necessary and re-attach after the unit is in place. Special rigging work
is best done by competent and experienced personnel working with proper equipment. Avoid short cuts.
GENERATOR LOCATION and MOUNTING:
As previously mentioned the location of the Marine Power System in the vessel is extremely
important. Follow the vessel manufacturer recommendations should they apply to your installation. All
key factors must be considered when choosing the mounting location for the unit. The engine and
generator end are mounted to a heavy gauge sheet metal base pan by 4 flexible isolators that help
prevent the transfer of vibrations from the generator to the mounting location. The unit must be
orientated on a level and structurally sound mounting platform, and securely bolted into place. Once the
unit mounting is completed the installer may begin attaching the component systems.
VENTILATION:
Most vessels are equipped with an ambient air ventilation system. If your vessel is not equipped
or insufficiently equipped to support the extra demand of a Marine Power System, provisions must be
made to install or increase the volume of ambient air into the area while providing for expulsion of hot
air and hazardous fumes.
2
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for PowerTech Marine Power System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of PowerTech Marine Power System in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info