582053

Powerplus POWXG8035LI Manual

3
Zoom out
Zoom in
Previous page
1/68
Next page
3
EN
Removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.
Removing the transportation locks
A
Donotremovethetransportationlocksbeforetaking
out the packaging reinforcement.
A
Remove the transportation safety bolts before operating
the washing machine, otherwise, the product will be
damaged.
1. Loosenalltheboltswithaspanneruntiltheyrotate
freely (C).
2. Remove transportation safety bolts by turning them
gently.
3. AttachtheplasticcoverssuppliedintheUserManual
bag into the holes on the rear panel. (P)
C
Keepthetransportationsafetyboltsinasafeplaceto
reuse when the washing machine needs to be moved
again in the future.
C
Never move the product without the transportation
safety bolts properly fixed in place!
Connecting water supply
C
Thewatersupplypressurerequiredtoruntheproduct
isbetween1to10bars(0.1–10MPa).Itisnecessary
tohave10–80litersofwaterflowingfromthefully
open tap in one minute to have your machine run
smoothly. Attach a pressure reducing valve if water
pressure is higher.
C
Ifyouaregoingtousethedoublewater-inletproduct
asasingle(cold)water-inletunit,youmustinstallthe
supplied stopper to the hot water valve before operating
the product. (Applies for the products supplied with a
blind stopper group.)
C
Ifyouwanttousebothwaterinletsoftheproduct,
connect the hot water hose after removing the stopper
and gasket group from the hot water valve. (Applies for
the products supplied with a blind stopper group.)
A
Models with a single water inlet should not be
connectedtothehotwatertap.Insuchacasethe
laundry will get damaged or the product will switch to
protection mode and will not operate.
A
Donotuseoldorusedwaterinlethosesonthenew
product.Itmaycausestainsonyourlaundry.
1. Connectthespecialhosessuppliedwiththeproductto
thewaterinletsontheproduct.Redhose(left)(max.90
ºC)isforhotwaterinlet,bluehose(right)(max.25ºC)is
for cold water inlet.
A
Ensure that the cold and hot water connections are
made correctly when installing the product. Otherwise,
your laundry will come out hot at the end of the washing
process and wear out.
2. Tighten all hose nuts by hand. Never use a wrench
when tightening the nuts.
3. Open the taps completely after making the hose
connection to check for water leaks at the connection
points.Ifanyleaksoccur,turnoffthetapandremove
the nut. Retighten the nut carefully after checking the
seal. To prevent water leakages and damages caused
by them, keep the taps closed when the machine is not
in use.
Connecting to the drain
• Theendofthedrainhosemustbedirectlyconnectedto
the wastewater drain or to the washbasin.
A
Your house will be flooded if the hose comes out of
its housing during water discharge. Moreover, there is
risk of scalding due to high washing temperatures! To
prevent such situations and to ensure smooth water
intake and discharge of the machine, fix the end of the
discharge hose tightly so that it cannot come out.
• Thehoseshouldbeattachedtoaheightofatleast40
cm,and100cmatmost.
• Incasethehoseiselevatedafterlayingitonthefloor
levelorclosetotheground(lessthan40cmabovethe
ground), water discharge becomes more difficult and
the laundry may come out excessively wet. Therefore,
follow the heights described in the figure.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXG8035LI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXG8035LI in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXG8035LI

Powerplus POWXG8035LI User Manual - German - 12 pages

Powerplus POWXG8035LI User Manual - Dutch - 11 pages

Powerplus POWXG8035LI User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info