480960
7
Zoom out
Zoom in
Previous page
1/11
Next page
POWX154 EN
Copyright © 2016 VARO P a g e | 7 www.varo.com
8.5 Mounting the chuck (fig. 8 & 9)
Open the safety guard (7).
Slide the chuck spindle (30) into the drive spindle.
The chuck (6) must be removed when working with cone drills. In order to remove the chuck,
proceed as follows:
Open the safety guard (7).
Lower the chuck until the hole in the drive spindle (31) becomes visible. Hold the chuck in
this position.
Raise the table until it is approximately 2 cm below the chuck.
Turn the chuck by hand to align the hole in the drive spindle with the holes in the feed
spindle.
Release the chuck by driving the wedge (32) into the hole in the drive spindle.
8.6 Inserting and removing a drill (fig. 10)
Open the safety guard (7).
Open the chuck (6).
Insert the drill into the chuck.
Fasten the chuck by hand.
Fasten the chuck firmly by inserting the chuck key in one of the holes in the side of the
chuck and turning it clockwise.
Shut the safety guard.
In order to remove a drill, proceed in reverse order.
Before inserting or removing a drill, always pull the plug from the wall
socket.
8.7 Setting the depth stop (fig. 11)
The depth stop is used to set the maximum drilling depth.
Set the required drilling depth by rotating the depth stop wheel (33) to the defined value.
8.8 Adjusting the table (fig. 12)
The table can be height-adjusted, turned and toppled.
Height adjustment:
Slacken the locking handle (34).
Turn the handle (19) to adjust the table (5) to the required height.
Tighten the locking handle.
Turning:
Slacken the locking handle (34).
Turn the table (5) to the required position.
Tighten the locking handle.
Toppling:
Slacken the locking screw (35).
Topple the table (5) to the required position.
Tighten the locking screw.
8.9 Adjusting the table extenders (fig. 13)
Using the table extenders you can support long workpieces.
Slacken the wing nuts (36).
Slide the extender (37) outward.
Tighten the wing nut.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX154 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX154 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX154

Powerplus POWX154 User Manual - German - 12 pages

Powerplus POWX154 User Manual - Dutch - 11 pages

Powerplus POWX154 User Manual - French - 12 pages

Powerplus POWX154 Additional guide - All languages - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info