677891

Powerplus POWX0760 Manual

20
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0760 EN
Copyright © 2014 VARO NV P a g e | 20 www.varo.com
10.2.9 Carrying tool (Fig. 66)
Make sure that the tool is unplugged. For the tool just used in the Mitre saw mode, secure the
blade at 0° bevel angle and the turn table at 0° Mitre angle. Lower the handle fully and lock it
in the lowered position by fully pushing in the stopper pin.
Carry the tool by holding the tool part shown in the figure. (Fig. 67)
CAUTION:
Always secure all moving portions before carrying the tool.
Before carrying the tool, always set up the tool in the Mitre saw mode.
Make sure that the lower blade guard C is installed on the tool.
11 MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and unplugged before attempting to perform
inspection or maintenance.
WARNING: Always be sure that the blade is sharp and clean for the best
and safest performance.
11.1 Adjusting the cutting angle
This tool is carefully adjusted and aligned at the factory, but rough handling may have affected
the alignment. If your tool is not aligned properly, perform the following:
11.1.1 Mitre angle
Mitre angle 0° adjusting bolts are located in four positions.
Loosen four Mitre angle 0° adjusting bolts by turning counterclockwise from the underside of
the table. (Fig. 68)
Lower the handle fully and lock it in the lowered position by pulling and rotating the stopper pin
to the angle of 90° clockwise. Square the side of the blade with the face of the guide fence
using a triangular rule, trysquare, etc. Then securely tighten the four adjusting bolts on the sub
arm from the underside of the table. Make sure that the pointer points to 0° on the Mitre scale.
If not so, adjust the pointer position by loosening the screw securing the pointer. After
adjusting it, securely tighten the screw. (Fig. 69)
11.1.2 Bevel angle
(1) 0° bevel angle
Lower the handle fully and lock it in the lowered position by pulling and rotating the stopper pin
to the angle of 90° clockwise. Loosen the lever at the rear of the tool.
Turn, from the underside of the table, the 0° bevel angle adjusting bolt on the right side of the
sub arm two or three revolutions counterclockwise to tilt the blade to the right. (Fig. 70)
Carefully square the side of the blade with the top surface of the turn table using the triangular
rule, try-square, etc. by turning the 0° bevel angle adjusting bolt clockwise. (Fig. 71)
Make sure that the pointer on the turn table point to 0° on the bevel scale on the arm. If it does
not point to 0°, loosen the screw which secures the pointer and adjust the pointer so that it will
point to 0°.
(2) 45° bevel angle Adjust the 45° bevel angle only after performing 0° bevel angle adjustment.
To adjust left 45° bevel angle, loosen the lever and tilt the blade to the left fully. Make sure that
the pointer on the arm points to 45° on the bevel scale on the arm. If the pointer does not point
to 45°, turn, from the underside of the table, the 45° bevel angle adjusting bolt on the left side
of the sub arm until the pointer points to 45°. (Fig. 72)
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0760 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0760

Powerplus POWX0760 User Manual - German - 27 pages

Powerplus POWX0760 User Manual - Dutch - 26 pages

Powerplus POWX0760 User Manual - French - 26 pages

Powerplus POWX0760 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info