725381
7
Zoom out
Zoom in
Previous page
1/11
Next page
POWX07595 EN
Copyright © 2020 VARO P a g e | 7 www.varo.com
7 OPERATION
Risk of injury! In the event of a functional fault, immediately press the red
button 0 on the On / Off switch and unplug.
7.1 Check before starting the device!
Risk of injury! The device may only be put into operation if there are no
defects. If a part is defective danger it must be replaced before the device is
used again.
Check to make sure the device is in safe operating condition:
Check to make sure there are no visible defects.
Check to make sure all device components are correctly mounted.
Check to make sure the safety equipment is functioning properly.
Check to make sure that the saw blade runs freely.
Check whether the adjusting screw for setting the angle of tilt is tightened.
7.2 Operating elements
7.2.1 On/off switch
Switching on: Pressing the green button I on the On / Off switch (1) switches on the saw.
Before starting to saw, wait until the blade has reached maximum speed.
Switching off: Pressing the red button 0 on the On / Off switch (1) switches off the saw.
7.2.2 Overload Protection (18)
The machine is fitted with an overload protection (18). Allow the machine to cool down for at
least 30 minutes before switching it on again. For this first press the black button next to the
switch, then press the green button (1) to restart the machine.
7.2.3 Setting mechanism for the tilt angle
The saw blade can be adjusted to any angle between 0° and 45°. Loosen the locking knob (3),
press the lever (2) and turn to the desired tilt angle and tighten the locking knob (3).
7.2.4 Hand crank for setting the cutting height
The cutting height of the saw blade must be adjusted to the height of the workpiece. The saw
blade must always be set to one blade tooth higher than the workpiece. You can set this by
turning the hand crank to left or right.
Note: In order to make use of the full range of 45° settings, the cutting
height must be reduced accordingly.
7.3 Workpiece stops
7.3.1 Mitre angle stop
The stop can be adjusted by a maximum of 120 mm for mitre cutting.
Risk of injury! Do not push the stop (Fig. 4 A) too far in the direction of the
saw blade. The gap between the stop (Fig. 4 A) and the saw blade should be
approximately 2 cm.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX07595 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07595 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07595

Powerplus POWX07595 User Manual - German - 12 pages

Powerplus POWX07595 User Manual - Dutch - 12 pages

Powerplus POWX07595 User Manual - French - 12 pages

Powerplus POWX07595 Additional guide - All languages - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info