675011
15
Zoom out
Zoom in
Previous page
1/19
Next page
POWX07551T EN
Copyright © 2016 VARO P a g e | 15 www.varo.com
Grasp and pull the switch handle (4) forward until the center of the saw blade is over the
front of the workpiece (3).
Engage the trigger to turn the saw on.
When the saw reaches full speed, slowly push the switch handle down, cutting through the
leading edge of the workpiece.
Slowly move the switch handle toward the fence, completing the cut.
Release the trigger and allow the blade to stop spinning before raising the cutting head
and removing the workpiece.
9.7 Cutting bowed material (Fig. 27)
A bowed workpiece must be positioned against the fence and secured with a clamp (1)
before cutting as shown. Do not position workpiece incorrectly or try to cut the workpiece
without the support of the fence. This will cause the blade to bind and could result in
personal injury.
9.8 Cutting grooves (Fig. 28)
WARNING: DO NOT USE A DADO BLADE, use only the standard saw blade
for this operation.
Mark lines to identify the width and depth of the desired cut on the workpiece and put the
workpiece on the table and aim the inside tip of the blade at the line. Use a clamp to
secure the workpiece on the table.
Lower the cutting head so the tip of the blade touches the top surface of the workpiece at
the marked line.
While holding the upper arm in position, turn the stop knob (2) until it touches the stop
plate (1).
Cut two parallel grooves as shown.
9.9 Auxiliary wood fence (Fig. 29)
When making multiple or repetitive cuts that result in cut-off pieces of one inch or less, it is
possible for the saw blade to catch the cut-off piece and throw it out of the saw or into the blade
guard and housing, possibly causing damage or injury. To minimize this, an auxiliary wood fence
(1) can be mounted to your saw. Holes are provided in the saw fence to attach an auxiliary wood
fence (this provides additional depth of cut). This fence should be constructed of straight auxiliary
wood approximately 3/4 in. thick by 1-1/2 in. high by 16 in. long. Attach the wood fence securely
and make a full depth cut to make a blade slot. Check for interference between the wood fence
and the lower blade guard. Adjust if necessary.
NOTE: This auxiliary fence is used only with the saw blade in the bevel
position (90° to the table). The auxiliary wood fence must be removed when
bevel cutting.
10 CLEANING AND MAINTENANCE
ATTENTION! !Before performing any work on the equipment, pull the power
plug.
10.1 Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use.
Keep the ventilation slots free from dust and dirt.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX07551T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07551T in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07551T

Powerplus POWX07551T User Manual - German - 21 pages

Powerplus POWX07551T User Manual - Dutch - 21 pages

Powerplus POWX07551T User Manual - French - 21 pages

Powerplus POWX07551T Additional guide - All languages - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info