480918
8
Zoom out
Zoom in
Previous page
1/10
Next page
POWX0395 EN
Copyright © 2013 VARO P a g e | 8 www.varo.com
8.5 General cutting
Clamp your work piece if it is portable. Rest the front shoe of the saw on your work piece (be
sure the blade is not contacting the work piece) and start the saw, exerting enough pressure in
the direction of the cut to keep the shoe pressed firmly against the work piece at all times. Do
not force the cut or stall the saw. Don’t bend or twist the blade, let the tool and the blade do
the work.
In general, coarser blades are for wood, plastics, and composites, and finer blades are
for cutting metal. Chattering or vibration may indicate you need a finer blade or higher
speed. If the blade overheats or clogs, it may indicate you need a coarser blade. Replace
blades when they become dull. Dull blades will produce poor
results and may overheat the saw.
8.6 Plunge cutting
Clearly mark the line of cut, from a convenient starting point within the cut out area. Place the
tip of the blade over that point with saw parallel to the line of cut, slowing lower the saw until
the bottom edge of the shoe rests on the work piece and the blade not touching the work piece.
Start the saw and allow it to attain full speed. With the saw resting on the shoe, slowly tilt the
saw forward to lower the blade onto the cut line. Continue this motion until the saw blade is
perpendicular to the work piece.
8.7 Metal cutting
Blades specifically designated for cutting metals must be used for this purpose. You may use
light oil as a coolant when cutting metal, this will prevent overheating of the blade, help the
blade cut faster, and promote longer blade life.
9 CLEANING AND MAINTENANCE
Attention! Before performing any work on the equipment, pull the power
plug.
9.1 Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use.
Keep the ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water.
Never use solvents such as petrol, alcohol, ammonia water, etc. These
solvents may damage the plastic parts.
9.2 Replacement f carbon brushes
Remove and check the carbon brushes regularly. Replace when they have worn down to the
limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon
brushes must be replaced at the same time. Only use original carbon brushes.
10 TECHNICAL DATA
Voltage / frequency
230-240V ~ 50Hz
Power input
710W
No load speed
0-2500 min-1
Max. cutting depth
115mm
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0395 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0395 in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0395

Powerplus POWX0395 User Manual - German - 11 pages

Powerplus POWX0395 User Manual - Dutch - 11 pages

Powerplus POWX0395 User Manual - French - 11 pages

Powerplus POWX0395 Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info