582660
8
Zoom out
Zoom in
Previous page
1/11
Next page
POWX0076LI EN
Copyright © 2013 VARO P a g e | 8 www.varo.com
9.2 Adjusting the depth of cut (Fig. 2)
The depth of cut is infinitely adjustable. A clean cut is achieved with the saw blade protruding
from the material by approx. 3 mm.
Loosen the lock lever for depth adjustment (5).
Hold the base plate (10) flat against the edge of the work piece and lift the body of the saw
until the blade is at the right depth determined by the depth gauge (4) (align the scale
line).
Tighten the lock lever for depth adjustment.
9.3 Setting the mitre angle (Fig. 3)
The mitre angle is infinitely variable between 0° and 45°.
Loosen the lock lever for angle adjustment (9).
Adjust the shoe to the desired angle between 0°to 45°. [See Angle gauge (8)].
Tighten the lock lever for angle adjustment.
9.4 Mounting the parallel fence (Fig. 4)
The parallel fence allows sawing parallel to an edge at a maximum distance of 10 cm.
Loosen the adjustment screw of guide bar (11).
Slide the guide bar (12) through the slots in the base plate to the desired width.
Tighten the adjusting screw to secure it in the position.
Ensure that the guide bar rests against the wood along its entire length to give consistent
parallel cuts.
10 OPERATION
10.1 Instructions for use
Clamp the workpiece. Make sure that the side which will be visible later is facing down,
because the cut is most accurate at that side.
Switch on the machine before it touches the workpiece. Do not exert pressure on the saw
blade. Allow the machine enough time to cut the workpiece.
Hold the machine with both hands using both grips. This ensures optimum control over the
machine.
For straight cuts along a drawn line use the marking for straight cuts.
For bevel cuts along a drawn line use the marking for bevel cuts.
10.2 Switching on and off (Fig. 5)
To switch the tool on, keep the lock-off button (2) depressed and press the on/off switch
(1).
To switch the tool off, release the on/off switch.
10.3 Dust extraction
A vacuum cleaner can be connected to the dust extraction outlet, either directly to the
connector or using an adapter.
If necessary, connect an adapter to the extraction outlet.
10.4 Laser beam
The laser beam is used for projection of the cut on the workpiece.
Switch the laser (14) on by means of the laser on/off switch (13).
Place the machine on the workpiece with the saw marking above the start of the cutting
line.
Check that the laser line aligns with the cutting line as marked on the workpiece.
Switch on the machine.
Follow the “instructions for use” to perform a cut.
After use , switch off the laser.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0076LI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0076LI in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0076LI

Powerplus POWX0076LI User Manual - German - 12 pages

Powerplus POWX0076LI User Manual - Dutch - 12 pages

Powerplus POWX0076LI User Manual - French - 12 pages

Powerplus POWX0076LI Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info