Manual Powerplus POWAIR0310 (page 3 of 8) (English)

582112

Zoom out

Zoom in

1/8

POWAIR0310 EN

 Repairs can only be effected by official dealers.

 To prevent injuries to yourself and bystanders, refer to tool use, maintenance and

troubleshooting sections for additional information (fig. 1).

 To prevent eye injuries, always wear safety glasses with hard plastic side shields.

Be sure everyone in your work area is wearing the same type of safety glasses (fig.

2).

 Always wear hearing protection and a hard hat (fig. 3).

 Never use hydrogen, oxygen, carbon dioxide or any other bottled gas as a power

source for this tool, the tool will explode and cause serious injury (fig. 4).

 Remove your finger from trigger when not driving fasteners. Never carry the tool with

finger on the trigger, the tool will eject a fastener when the safety is pressed (fig. 5).

 Never connect the tool to an air hose with pressure exceeding 200 psi or 13.7 bar

(fig. 6).

 Air compressors must comply with requirement ANSI B19.3 1981 (U.S.), "Safety

Standard for Compressors for Process Industries" (fig. 7).

 Air hose minimum working pressure rating of 150 psi (10.3 bar) or 150% of the

maximum pressure produced in the system is absolutely necessary (fig. 8).

 The tool and air supply hose must have a hose coupling such that all pressure is

removed from the tool when the coupling joint is disconnected (fig. 9).

 Use only compressed air coming through 3 pieces set (fig. 10).

 Never load the tool if it is connected to air supply (fig. 11).

 Never use the tool if the safety element, trigger or springs have become inoperative,

missing or damaged. It is hazardous to remove the safety element, trigger or spring

(fig. 12).

 Before using this tool, make sure trigger, screw and cap are securely tightened (fig.

13).

 Do not modify tool without authorization (fig. 14).

 Disconnect the tool from the air supply whenever the tool stops working (fig.15).

 Keep the tool pointed away from yourself and others (fig. 16).

 Fire fasteners into work surface only, never into materials too hard to penetrate (fig.

17).

 Do not drive fasteners on top of other fasteners. Firing the tool in an inclined angle is

also forbidden (fig. 18).

 Do not push safety element on work surface until a second fastener is desired (fig.

19).

 Do not drive fasteners close to the edge of the work surface. The work piece is likely

to split and the fastener could fly free and hit someone (fig. 20).

 Do not load fasteners with trigger or safety element depressed (fig. 21).

 Do not use tool without Danger-label on tool (fig. 22).

 Never use a tool that leaks air or needs repair (fig. 23).

 Be sure you are in a balanced position when using or handling the tool (fig. 24).

 Operate the tool at recommended pressure of 4-8 bar.

5 ADDITIONAL INSTRUCTIONS FOR FASTENER DRIVING TOOLS OPERATED BY

COMPRESSED AIR

 fastener driving tools operated by compressed air shall only be connected to

compressed air lines where the maximum allowable pressure cannot be exceeded

by a factor of more than 10%, which can for example be achieved by a pressure

reduction valve which includes a downstream safety valve;

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWAIR0310 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWAIR0310

Powerplus POWAIR0310 User Manual - German - 9 pages

Powerplus POWAIR0310 User Manual - Dutch - 9 pages

Powerplus POWAIR0310 User Manual - French - 9 pages

Powerplus POWAIR0310 Additional guide - All languages - 3 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Powerplus POWAIR0310 Manual

Product: