582171
5
Zoom out
Zoom in
Previous page
1/7
Next page
POW5100 EN
Copyright © 2015 VARO P a g e | 5 www.varo.com
It is compulsory to wear certified gloves and protective goggles when using the device.
Never use the machine without its protective guard and “spark guards”.
Always check that the work supports are firmly fixed before using the machine.
As the wheel wears down, adjust the work support and screen slide:
1.5mm between the work support and the wheel
2mm between the slide and the wheel
When using the grinder, stand in a stable, balanced position, without stretching, and keep
children at a distance.
Never leave the machine running unsupervised. Keep the workshop clean and tidy.
Before use, make sure the grinding wheels are not damaged or cracked. If there is the
slightest doubt, replace at once (a damaged grinding wheel can fly apart at speed).
Replacement grinding wheels must be identical in characteristics and dimensions.
This machine is not suitable for grinding soft substances such as lead, magnesium or light
alloys.
7 ASSEMBLY
ATTENTION! Disconnect the power plug before carrying out any
adjustments or maintenance.
Fit the work supports (10) using the bolts supplied. Set these work supports not more than
2mm from the grinding wheel.
Fit the transparent protection screens (6), (7) using the screws supplied, over the wheel
guards. The clearance between the slide (7) and the wheel must not exceed 2mm.
Whenever the machine is used, the screen must be in low position.
It is strongly recommended that the grinder should be bolted to a bench or work table. The
length of the bolts will be determined by the thickness off the bench top. The machine
must be fixed by 4 bolts in the places provided for them in the base (1). The grinder is
fitted with rubber “anti-vibration” shoes. Nevertheless, the inclusion of a piece of soft wood
between the base and the bench is recommended for better absorption of vibrations.
8 OPERATION
This machine is designed for sharpening tools or grinding small parts. It is not suitable for
grinding heavy sheet metal parts.
Use the appropriate grinding wheel for the job: the “SOFT” wheel for hard metals / the
“HARD” wheel for soft metals.
Do not grind wood, plastic, soft alloys (e.g. lead) or similar materials, as this would clog
the grinding wheels.
Apply gradually increasing pressure to the part to be ground, which must not be brought
into sudden contact with the grinding wheel.
For prolonged grinding operations, cool the work at regular intervals in water. Some tools
(e.g. wood chisels) must not be ground “blue”.
Hold the work-piece firmly so that it cannot jam between the grinding wheel and the
support (with risk of damage or even fracture of the wheel).
Changing the grinding wheel (tools required: wrench 19mm wrench 8mm cross-head
screwdriver): Machine disconnected
remove the spark-guard (6) or (7) and wheel guard (5) or (9),
unscrew wheel fixing nut
Warning: seen from in front, the shaft on the right has a right-hand
(conventional) thread, and the shaft on the left a left-hand thread.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW5100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW5100 in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW5100

Powerplus POW5100 User Manual - German - 8 pages

Powerplus POW5100 User Manual - Dutch - 8 pages

Powerplus POW5100 User Manual - French - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info