480967
5
Zoom out
Zoom in
Previous page
1/8
Next page
POW30543 EN
Copyright © 2015 VARO NV P a g e | 5 www.varo.com
Chisel bits and drill bits may be flung out of the machine accidentally and cause serious
injury:
Before starting to work, always check that the chisel or drill bit is properly locked in the
chuck.
Never start up a hammer tool until it is pressed against a workplace (wall, ceiling, etc.).
When you are finished, unplug the hammer drill from the electric supply and remove the
chisel or drill bit from the machine.
Always disconnect the hammer drill from the electric supply before you change a chisel or
drill bit.
Protect your eyes and other workers from flying particles and splinters. Wear a helmet! Set
up partition walls!
Wear work gloves to protect fingers from bruising and grazing.
Vibrations can injure the hand-arm system. Keep exposure to vibrations as short as
possible.
Always lead the mains cable away backwards from the device
Store the device where it is inaccessible to children.
When carrying out work, always hold the device with both hands and ensure that you have
a stable standing position.
7 BEFORE STARTING WORK
Examine the place where the device is to be used for hidden electrical cables, gas and
water pipes using a pipe finding device.
Before connecting to !he mains, ensure care that the mains voltage corresponds to the
details on the rating plate.
7.1 Fitting and changing tools (Fig 2)
The device is equipped with a SDS-plus attachment system.
Clean tools and grease with a thin layer of machine grease before fitting.
Pull back fastening sleeve and hold.
Push and rotate the dust-free tool into the tool holder as far as it will go, The tool will lock
automatically.
Check that it has locked by pulling the tool
7.2 Removing SDS-plus tool (Fig 3)
Pull back fastening sleeve, hold and remove tool.
8 STARTING WORK
8.1 Switching ON/OFF
Switching on: Press the operating switch.
Switching off: Press the operating switch briefly and let go.
8.2 Handle attachment (Fig 4)
For reasons of safety, only use the hammer drill with handle attachment.
You will be able to obtain a safe body position when working by rotating the handle attachment.
Loosen and turn the handle attachment in an anti-clockwise direction: Then tighten the handle
attachment.
8.3 Depth stop (Fig 5)
Loosen the handle attachment and place the straight part of the depth stop in the hole. Adjust
the depth stop and retighten the handle attachment.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW30543 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW30543 in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW30543

Powerplus POW30543 User Manual - German - 9 pages

Powerplus POW30543 User Manual - Dutch - 9 pages

Powerplus POW30543 User Manual - French - 9 pages

Powerplus POW30543 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info