582168
6
Zoom out
Zoom in
Previous page
1/9
Next page
POW2085 EN
Copyright © 2014 VARO P a g e | 6 www.varo.com
7.2 Mounting a grinding disc (Fig.2 3)
Use grinding discs of the correct dimension. Use fibre-reinforced grinding discs only. The
grinding disc must not touch the edge of the guard.
Press the spindle lock and turn the spindle (2) until it engages in the lock. Keep the
spindle lock pressed during this procedure.
Retrieve the outer flange nut (A) from the spindle using the spanner (9).
Position the grinding disc (C)on the backing flange (B).
Place the outer flange nut (A) on the spindle an tighten using the spanner (9).
Release the spindle lock (2) and check that the spindle is unlocked by rotating it.
7.3 Mounting the side handle (Fig. 4)
The auxiliary handle can be attached to the angle grinder in two different mounting holes (10):
left and right.
The side handle can be used for both left-hand and right-hand control.
Fasten the side handle for left-hand operation on the right-hand side of the machine.
Fasten the side handle for right-hand operation on the left-hand side of the machine.
Fasten the side handle for upright working at the top of the machine.
Make sure that the side handle is fastened propperly and cannot loosen
unexpectedly.
8 OPERATION
Do not place the machine on the work piece when switching the machine on or off. The
grinding disc may damage the work piece.
Clamp the work piece and make sure that the work piece cannot slide from under the
machine during the cutting activities.
Hold the machine firmly and press it under an angle of approximately 15' against the work
piece. Move the grinding disc evenly across the work piece.
Regularly inspect the grinding disc. Worn grinding discs have a negative effect on the
efficiency of the machine. Replace a grinding disc on time.
Always switch off the machine first before removing the plug from the wall socket.
8.1 Switching on and off
You need to first press the switch button at its rear end and then push it forward to start
the tool
To switch off, depress the on/off switch, this will then jump to the ‘off’ position.
WARNING
Do not put the machine down when the motor is still running.
Do not place the machine on a dusty surface. Dust particles may enter the mechanism.
Never use the spindle lock to stop the motor.
Never use the machine for grinding magnesium work pieces.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW2085 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW2085 in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW2085

Powerplus POW2085 User Manual - German - 10 pages

Powerplus POW2085 User Manual - Dutch - 10 pages

Powerplus POW2085 User Manual - French - 10 pages

Powerplus POW2085 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info