582160
5
Zoom out
Zoom in
Previous page
1/8
Next page
POW1015 EN
Copyright © 2013 VARO P a g e | 5 www.varo.com
6 SPECIAL SAFETY INSTRUCTIONS FOR JIG SAWS
Important! Use of any accessories or attachments other than those
supplied or recommended in these operating instructions can mean the risk
of injury.
When using jig saws ear protectors and a face mask should be worn. Exposure to noise
can cause damage to hearing.
Do not use the jig saw to cut asbestos or materials containing asbestos.
Do not leave power tools running unattended. Always switch off and do not put down or
leave until it has stopped completely.
Long hair must be covered. Do not work in loose fitting clothing.
Be careful when working on walls. Damage to power supply lines, gas or water pipes can
lead to dangerous situations. Use appropriate detectors to establish whether there are
concealed wires or pipes in the working area.
Always check that the mains voltage corresponds to the voltage on the device's rating
plate.
Secure the work piece. The work piece is only secure if it is held by work-holding devices
or in a vice.
Use of extension cables. Only use extension cables which are designed for the machine's
power. The minimum conductor cross section must be 1.5 mm². When using cable reels
the cable must always be completely unrolled.
Always remove the mains plug before replacing saw blades.
Caution: saw blades can get very hot.
Saw blades must be kept sharp and in good condition. Replace partially fractured and
broken saw blades immediately.
Work calmly and evenly with the jig saw. You will thus avoid accidents and the saw blades
and the jig saw will last longer.
7 OPERATING INSTRUCTIONS
7.1 Starting up
7.1.1 Instant response operation
Switching on: Press the On/Off switch.
Switching off: Release the On/Off switch.
7.1.2 Continuous operation
Switching on: Press the On/0ff switch, keep pressed and lock with the locking button
Switching off: Press the On/Off switch and release
7.1.3 Electronic speed control setting
Using the knurled screw on of the handle you can pre-set any speed. Turn the knurled screw
to a higher number for a higher speed and turn it to a lower number for a lower speed. The
ideal cutting rate depends on the specific material and working conditions.
The general rules for tool speed in cutting operations apply.
7.2 Changing the saw blade
Tilt the transparent cover to the top. Push the lever from saw clamp blade to the front, place
the saw blade in the clamp and push it to the top until the lever from the saw blade clamp
moves to the back (locking position).
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POW1015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POW1015 in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POW1015

Powerplus POW1015 User Manual - German - 9 pages

Powerplus POW1015 User Manual - Dutch - 8 pages

Powerplus POW1015 User Manual - French - 9 pages

Powerplus POW1015 Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info