382559
5
Zoom out
Zoom in
Previous page
1/8
Next page
POWX033 EN
Copyright © 2015 VARO NV P a g e | 5 www.varo.com
Caution: saw blades can get very hot.
Saw blades must be kept sharp and in good condition. Replace partially fractured and
broken saw blades immediately.
Work calmly and evenly with the jig saw. You will thus avoid accidents and the saw blades
and the jig saw will last longer.
7 OPERATION
7.1 Switching On & Off
7.1.1 Instant response operation (Figure 1)
Switching on: Press the On/Oft switch
Switching off: Release the On/Off switch
7.1.2 Continuous operation
Switching on: Press the On/Off switch, keep pressed and lock with the locking button
Switching off: Press the On/Off switch and release
See Fig 1.
A : Locking button
B : On/Off switch
7.2 Changing the saw blade (Figure 2)
Switch off the jigsaw and remove the plug from the power socket before changing the blade or
carrying out any other work on the jigsaw.
Use the supplied hexagon-socket spanner to undo the two screws on the ram (Figure 2). Slide
the saw blade into the guide slot and up to the stop between the piston rod and the retention
clip. Use the supplied hexagon-socket spanner to tighten the two screws. The teeth of the saw
blade must face in cutting direction. Make sure that the saw blade sits property in the guide
slot of the ram and roller.
Important: Make sure that the saw blade sits properly in the slot of the roller and ram.
See fig 2 (Releasing the saw blade: Turn screw anticlockwise.)
7.3 Electronic speed control setting (Figure 3)
Using the knurled screw on the On/Off switch you can pre-set any speed.
Turn the knurled screw in PLUS direction for a higher speed and turn it in MINUS direction for
a lower speed.
The ideal cutting rate depends on the specific material and working conditions.
The general rules for tool speed in cutting operations apply.
See Fig 3
(1) turn the speed controller to increase the cutting rate.
7.4 Adjusting the base
(for mitering and sawing near edges, Figure 4)
For mitre and bevel cuts you can swivel the base by up to 45° in either direction after undoing
the two screws on the bottom The angles 15°, 30° and 45° are marked but you can adjust the
saw to any angle between these markings as required.
To adjust the cutting angle, undo the two screws (Figure 4) until you can just about move the
blade. Adjust to the required angle and re-tighten the two screws.
To enable you to saw right up to the edge, the base can be pushed backward. To do so, undo
the two screws underneath (Figure 4) and push the base to the back. Re-tighten the two
screws.
See FIG 4
Undo the two screws to set the base to an angle of 0° to 45° on the right or left side.
5


Need help? Post your question in this forum.

Forumrules
1

Forum

powerplus-pow-x033

Reset search

  • What size grub screws secure saw blade for a powerplus xo33 fretsaw Submitted on 13-5-2022 at 17:10

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus pow x033 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus pow x033 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus pow x033

Powerplus pow x033 User Manual - German - 9 pages

Powerplus pow x033 User Manual - Dutch - 9 pages

Powerplus pow x033 User Manual - French - 10 pages

Powerplus pow x033 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info