388483
5
Zoom out
Zoom in
Previous page
1/8
Next page
POW30610 EN
Copyright © 2012 VARO Page | 5 www.varo.com
§ Do not burn the battery.
§ Never attempt to open the battery.
§ In case of skin contact of the battery fluid (a solution of 25-30% potassium hydroxide),
flush immediately with abundant water. Neutralize with a mild acid such as lemon juice or
vinegar. In case of eye contact, rinse abundantly for 10 minutes with clean water and
consult a physician.
8 OPERATION
8.1 Charging the battery (fig. B)
The battery (6) must be charged before first use. Only after several charge and discharge
cycles the battery will attain full capacity.
§ Remove the battery from the machine.
§ Connect the battery to the charger.
§ Insert the mains adaptor of the charger into a mains outlet. Red LED lights. The green
charging indicator lights when the battery is charged. Never charge the battery for more
than 5 hours. If the indicators do not light, the battery may be too warm. In this case let the
battery cool down before charging.
8.2 Positioning and removing a drill or screw bit
This tool is equipped with a keyless chuck.
§ Open the chuck by turning the collar.
§ Insert the drill or screw bit in the chuck.
§ Close the chuck by firmly tightening the collar while holding the rear part of the chuck with
the other hand.
§ In order to remove the drill or screw bit proceed in reverse order. Before positioning or
removing a drill or screw bit always remove the battery from the machine.
8.3 Forward/reverse switch (fig. A)
§ Push the forward/reverse switch (2) from left to right side to drill holes and fasten screws.
(push L)
§ Push the forward/reverse switch (2) from right to left side to loosen screws. Always wait
until the motor has come to a complete standstill before changing the direction of rotation.
8.4 Adjusting the torque (fig. C)
This machine has been fitted with an adjustable coupling (15+1 pos) to limit the torque when
tightening screws .
§ Turn the adjustment collar (3) clockwise to reduce the torque and counterclockwise to
increase the torque. The correct setting depends on the type and size of the screw and the
work piece.
§ In case of doubt, start with the lowest setting and increase the torque until you have
reached the desired result.
§ For drilling, turn the adjustment collar fully counterclockwise (to the drilling symbol).
8.5 Switching on and off (fig. A)
§ To switch on the machine, press the on/off switch (1).
§ To switch off the machine, release the on/off switch.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus pow 30610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus pow 30610 in the language / languages: English as an attachment in your email.

The manual is 0,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus pow 30610

Powerplus pow 30610 User Manual - German - 9 pages

Powerplus pow 30610 User Manual - Dutch - 9 pages

Powerplus pow 30610 User Manual - French - 9 pages

Powerplus pow 30610 Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info