628483
83
Zoom out
Zoom in
Previous page
1/85
Next page
This command is a boolean command. See Section 6.1 for more information on this type of command.
This command is saved to non-volatile memory only as part of a preset. The state of this command will
be restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
T01SSEN1
Enable screen saver.
T01SSEN1
T01SSEN0
Disable screen saver.
T01SSEN0
T01SSEN2
Toggle screen saver enabled state.
T01SSENx, where x is 0 or 1 depending on the
current enabled state of the scrren saver.
T01SSEN?
Query screen saver enabled state.
T01SSENx, where x is 0 or 1 depending on the
current enabled state of the scrren saver.
8.109. SSSTART -- Set Idle Time Required for Screen Saver
to Start
This command sets or queries the amount of time (in milliseconds) that the front panel buttons must be
idle before the screen saver starts.
This command is an integer command. See
Section 6.2 for more information on this type of command.
The minimum and maximum values for this command are 500 and 600000, respectively.
This command is saved to non-volatile memory only as part of a preset. The state of this command will
be restored after power-up only if a preset is saved and that preset is set to be the power-on preset.
Example Description Status Message
T01SSSTART2000
Set screen saver start time to 2
seconds (2000 ms).
T01SSSTART2000
T01SSSTART>500
Increase screen saver start time
by 0.5 seconds (500 ms).
T01SSSTARTx, where x is the new value of the
screen saver start time. If this command was
issued after the example above, then the status
message would be T01SSSTART2500.
T01SSSTART?
Query screen saver start time.
T01SSSTARTx, where x is the new value of the
screen saver start time. If this command was
issued after the example above, then the status
message would be T01SSSTART2500.
8.110. SSTEXT -- Set Text to be Displayed by Screen Saver
This command sets or queries the text messages displayed by the screen saver. The arguments of this
command are the screen number, the line number, and the text to be displayed. The screen number
must be between 0 and 3. It indicates which message screen we are trying to set or query. Each
message screen consists of two lines of text that can be up to 16 characters long. The second number
indicates which line of the message we are tring to set or query. The line number must be 0 or 1
83


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polycom Vortex EF2201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polycom Vortex EF2201 in the language / languages: English as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polycom Vortex EF2201

Polycom Vortex EF2201 User Manual - English - 43 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info