E
E
N
N
G
G
L
L
I
I
S
S
H
H
VAPORELLA FOREVER 1400
30
S
S
H
H
O
O
R
R
T
T
A
A
G
G
E
E
O
O
F
F
W
W
A
A
T
T
E
E
R
R
The lack of water in the tank (3) is signalled
by the indicator light (C) coming on.
To return to ironing, proceed as follows:
• Fill the tank (3) again, as described in the
paragraph “PREPARATION”.
• Press the “RESET” button (5) to cancel the
shortage of water alarm. The indicator light
(C) will go out.
P
P
U
U
T
T
T
T
I
I
N
N
G
G
A
A
W
W
A
A
Y
Y
T
T
H
H
E
E
A
A
P
P
P
P
L
L
I
I
A
A
N
N
C
C
E
E
Make sure the appliance has cooled down
completely before putting it away.
• Tug on the power cable gently (9) until it
clicks once, and then accompany it with
your hand as it is automatically wound up
by the cable winder (9a).
• Position the flex (steam and electric) (8) in
the specific housing (8a) (fig. 6).
• Carry the Vaporella by its convenient carry
handle (1) (fig.6).
ATTENTION:
before moving Vaporella by its
carry handle, ensure that you have replaced
the power supply cable (9) and flex (steam
and electric) (8) as described previously.
E
E
N
N
E
E
R
R
G
G
Y
Y
S
S
A
A
V
V
I
I
N
N
G
G
S
S
T
T
A
A
N
N
D
D
-
-
B
B
Y
Y
F
F
U
U
N
N
C
C
T
T
I
I
O
O
N
N
After 10 minutes of the appliance not being
used, it automatically goes into stand-by
mode. Both the boiler and iron are switched
off.The indicator lights (A), (B) and (C) flash
simultaneously.
To re-activate the appliance, press the steam
request button (10).
N.B.: The stand-by function will not be ap-
plied if the steam flow control knob (6) is set
to "DRY".
C
C
A
A
R
R
E
E
O
O
F
F
Y
Y
O
O
U
U
R
R
V
V
A
A
P
P
O
O
R
R
E
E
L
L
L
L
A
A
• Before attempting any maintenance
operation, always disconnect the ap-
pliance from the mains.
• To clean the body of the appliance, simply
use a moist cloth. Do not use solvents or
detergents which may harm the body mate-
rial.
C
C
L
L
E
E
A
A
N
N
I
I
N
N
G
G
T
T
H
H
E
E
B
B
O
O
I
I
L
L
E
E
R
R
• Disconnect the appliance and let it cool
down for at least 2 hours.
• Empty the water tank to prevent leakage.
• Turn the appliance upside-down and use
the hexagon wrench (13) to unscrew the
boiler cap (12) on the bottom of the ap-
pliance (fig.7).
• Use the funnel (14) to pour 1/4 litre of cold
water into the boiler.
CAUTION: do not pour more than the
specified amount of water into the boi-
ler. Pour water slowly, being careful not
to let it overflow, as this could damage
the appliance (fig.8).
• Rinse out the boiler and pour the water
away into the sink or into a container for
collecting dirty water.
• If the water is very dirty, repeat the opera-
tion until it is clean.
• Put the cap back on the boiler, checking
that the seal is present and that the cap is
screwed on properly.
• Fill the water tank again and put the cap
on.
• Turn the appliance on again.
• Before ironing, release steam into the sink
or another container and check that the
steam is clean. This should take a few se-
conds.
• Resume ironing normally.
• To maintain optimum performance, clean
the boiler every 10/20 uses depending on
the amount of limestone in the water.
