648804

Polti Sani System Polti Manual

6
Zoom out
Zoom in
Previous page
1/8
Next page
Switch on the “Sani System Polti” machine fol-
lowing the manufacturer’s instructions. Once
the system is ready, distribute the steam and
HPMED sanitising agent. Mixed with the
steam, the product will dry within 30 seconds
to one minute, depending on the environmen-
tal conditions.
Warnings :
Keep out of the reach of children. Do not in-
gest. In case of contact with eyes, rinse with
plenty of water and seek medical advice.
A safety data sheet is available for profes-
sional users.
For professional use only.
HPMED is a cleaning sanitisin product for hard
surfaces. Contains <5% non-ionic surfactant.
(EEC Reg. 648/2004).
P
P
R
R
E
E
P
P
A
A
R
R
I
I
N
N
G
G
F
F
O
O
R
R
U
U
S
S
E
E
• Unscrew the cap (G) from the tank and fill
the tank with about 4.5l of normal tap water.
Disconnecting of the device from the power
mains before filling is recommended.
• Fit the carrier grip as shown in Fig.1, tighten-
ing the two screws on the rear of the grip to
secure it in place.
• Insert the tube-holder rod (L) into its hole
(Fig.2).
• Plug the power cable (H) into the panel-type
socket on the rear of the device. Plug the
connector on the other end of the power
cord into a suitable socket with an earth con-
nection.
• Fit the disposable bottle into the delivery de-
vice following the instructions in paragraph
“DISPOSABLE BOTTLE OF HPMED”.
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
S
S
F
F
O
O
R
R
U
U
S
S
E
E
• Turn the main switch (A) to the "I" position.
• Press the boiler switch (B). The “Steam
Ready” lamp (C) will start to flash. Wait for
the flashing lamp (C) to remain steady on
(about 5 to 10 minutes). This indicates that
the device is ready to be used.
• Press the steam delivery push-button (P) so
that steam will be delivered through the noz-
zle. The “Delivery” lamp (N) will switch off
when the heating coil inside the nozzle
reaches the working temperature.
The steam delivery button (P) should be in
the “Safe Position”, so as to avoid accidental
delivery of steam.
Note:
• While the device is being used, the “Steam
Ready” lamp (C) will start flashing instead of
remaining steady on, and the delivery lamp
(N) will light up and then turn off. This indi-
cates that the electric heating coils have
switched on in order to keep the pressure in
the boiler and the temperature in the deliv-
ery nozzle up. This is a normal occurrence,
and it is therefore possible to continue the
sanitising operations.
• BEFORE STARTING TO SANITISE, IT IS
ADVISABLE TO DIRECT THE FIRST JET
OF STEAM ONTO A CLOTH OR DOWN-
WARDS FOR APPROXIMATELY 30 SEC-
ONDS WITHOUT HOOKING UP THE FIT-
TING FOR THE DISPOSABLE BOTTLE
(Q). THIS WILL ENABLE THE OPTIMUM
TEMPERATURE AND PRESSURE TO BE
REACHED.
T
T
I
I
P
P
S
S
F
F
O
O
R
R
U
U
S
S
E
E
Before treating delicate or special surfaces
with the SANI SYSTEM Polti sanitising sys-
tem, consult the manufacturer’s instructions
and carry out a test on a hidden part of the sur-
face or on a sample of the material.
Allow the sanitised part to dry to make sure
that no changes in colour or deformations
have occurred.
Make sure that the surface to be treated is
clean before sanitising it. In the event of
visible dirt, clean the surface before sani-
tising it.
Direct the steam downwards for 2 seconds
in order to bring all the components of the
machine to their correct temperature, in or-
der to avoid condensation.
Bring the delivery nozzle into a position per-
pendicular to the surface to be sanitised and
keep it at a distance of 10 cm, as provided by
the spacer, avoiding direct contact of the latter
with the surface. Deliver the steam on a con-
tinuous movement, using “brushing” move-
ments to cover the surface to be sanitised.
SANI SYSTEM POLTI
37
E
E
N
N
G
G
L
L
I
I
S
S
H
H
SANI SYSTEM 02 M0S08288 1O05:A5 06/06/2008 17.05 Pagina 37
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polti Sani System Polti at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polti Sani System Polti in the language / languages: English as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info