Manual Polti prof 1300 (page 5 of 6) (English)

323420

Zoom out

Zoom in

1/6

• Polti declines liability for any damage or

accident derived from any use of VAPO-

RELLA which is not in conformity with the

instructions contained in this booklet.

1a.Unscrew the patented safety cap (5) and fill

the boiler with about 0.9 litres of water using

the special funnel (9) making sure that it does

not overflow (fig. 1).

Normal tapwater can be used. However, as

hard water by its nature contains limestone,

which may cause a build-up of limescale in

the tank, in hard water areas we recommend

the use of our natural-base decalcifier

Kalstop FP 2003.

2a.Retighten the cap fully and carefully. Ensure

the patented safety cap (5) is fully and correc-

tly screwed on, otherwise you may experien-

ce steam escaping from around the cap.

3a.Connect the power supply cable into an ear-

thed power supply of the correct voltage.

4a.Switch on the boiler and iron by pressing the

switches (2) and (4) (fig. 2).

NOTE: during the filling operation, be careful that

the water does not overflow as it may come out

and wet the surface where Vaporella is laid.

STEAM IRONING

1b.Set the iron temperature to the “COTTON -

LINEN” steam position (fig. 3), by turning the

knob (1). All types of fabric can be ironed at

this temperature.

2b.Wait until the boiler switch (2) and the “Iron

heating” indicator light (3a) switch off (about

15 minutes). Press the button (3) on the iron

to release steam out of the steam holes on

the soleplate. Releasing the button, the

steam stops.

3b.In order to have a continuous steam jet, move

the button (3b) forwards. Steam will keep on

coming out, even if you release the button. To

interrupt the outlet, move the button (3b)

backwards (fig. 4).

NOTE: during initial operation of the iron, a

few drops of water mixed with steam may

come out of the soleplate until the temperatu-

re stabilises. It is advisable to direct the first

jets of steam onto an old cloth until a uniform

stable jet of steam is obtained.

DRY IRONING

1c.For dry ironing:

• Plug the cable in.

• Press the iron switch (4), leaving the boiler

switch (2) off .

• Adjust the soleplate temperature turning the

knob (1) setting to the temperature required

according to the type of fabric.

NOTE:

• The boiler switch (2) and the “Iron heating”

indicator light (3a) goes on and off during

usage. This means that the heating element is

working correctly to keep a constant pressure

in the boiler. This is a correct functioning, just

continue ironing as normal.

• If no steam is released from the iron, check the

following: the “Iron heating” indicator light (3a)

is switched off; there is water in the boiler.

““

””

Your Vaporella is equipped with the unique Polti

patented safety cap, which prevents opening of

the generator tank as long as there is any pres-

sure remaining inside the tank. This is an impor-

tant and indispensable safety device, and it is

necessary to follow certain procedures when re-

filling the tank.

When you have used up all the water in the tank,

do as follows:

1d.Switch off the boiler on/off switch (2).

2d Press the steam request button on the iron

(3) so as to fully exhaust the steam supply

from the tank.

3d.Switch off the iron switch (4) .

4d.Disconnect the power supply cable from the

mains.

5d.Unscrew anti-clockwise the patented safety

cap (5).

VAPORELLA

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Polti prof 1300 in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Polti prof 1300 Manual

Product: