Manual Polaroid Impossible Instant Lab Universal (page 8 of 10) (English)

694110

Zoom out

Zoom in

1/10

STARTING THE EXPOSURE

FINISH THE EXPOSURE

EJECTING THE PHOTO AND

HANDLING IT CORRECTLY

AFTER USE

Roller System

When ready, place your device on the

Universal Cradle with screen face-

down and the ﬂash facing up towards

you. The top of your device should

point in the same direction as the

direction your photo leaves the Instant

Lab Universal. Once on the cradle,

you will hear a sound to indicate a

successful connection, or one that

indicates a failure. Some devices

will also use the ﬂash to indicate the

successful connection. When you hear

the ‘success’ sound and you see the

ﬂash, pull the shutter slide

all the

way out. Do this within 5 seconds of

hearing the success sound.

Note iPod and most Android devices will

sound an alert instead of the ﬂash.

When you hear the shutter camera

sound (in some devices, the device’s

ﬂash will also go off), push the shutter

slide

back in. Once the shutter

slide is back in, you can safely remove

your device off the cradle.

Press and hold the eject button

to eject your instant photo. With older

generations of Impossible ﬁlm (for

example: early editions like Silver

Shade and Generation 1.0), you will

need to shield your photo from light

during development.

For Generation 2.0 ‘no shield’ ﬁlm, you

can watch your photo develop without

shielding the image. See individual

ﬁlm packaging for details.

Remove your device and replace the

cradle cover

to protect the lens.

Press tabs

on either side of each

tower section to collapse the tower.

Cleaning the Instant Lab Universal

Always unplug the Instant Lab

Universal from the power adaptor

before cleaning.

Exterior

Wipe gently with a soft cloth. If the

Instant Lab Universal is very dirty, soak

the cloth in mild soapy water and wring

well before use. Wipe the Instant Lab

Universal with a damp cloth and then

dry with a dry, clean cloth.

When cleaning the

rollers, use a moist cotton swab or

cloth. Do not use a paper tissue as this

could get stuck between the rollers.

Using a small amount of either warm

water or alcohol, press the swab gently

onto the rollers and press the eject

button, which will turn the rollers. Do

not turn the rollers forcibly by hand!

Repeat several times until clean. Do

not use an excess amount of water

or alcohol as ﬂuid may drip onto the

electronics and damage them.

Lens Dust can be removed with a

blower brush. Fingerprints can be

removed by breathing on the lens and

then wiping it with a lens cloth or

tissue. Persistent dirt can be removed

by applying a small amount of lens

cleaning ﬂuid to the cloth.

Note Mold may form on the lens surface if

the lens is left dirty.

Charger Wipe gently with a soft, dry

cloth.

Note Do not use strong solvents such as

benzene or alcohol or a chemically treated

cloth on parts other than the metal rollers.

Storing the Instant Lab

Do not leave the Instant Lab

Universal in an environment with high

temperatures (40°C / 104°F or more)

or low temperatures (-10°C / 14°F or

less.) Failure to do so may impact the

battery life.

Do not use the Instant Lab Universal

in the rain or allow water to enter the

device. Do not pour water over the

Instant Lab Universal.

When storing the Instant Lab Universal

for extended periods, keep it in a

cool, dry place that is well ventilated.

The battery will lose its power within

a period of several months. It is

recommended that you recharge the

battery every 3 – 5 months to extend

the battery life.

Note Do not store the Instant Lab Universal

in direct sunlight, in hot vehicles or near

heat sources. Avoid leaving the device

in places where chemical products are

handled as this may result in corrosion.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Polaroid Impossible Instant Lab Universal in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Polaroid Impossible Instant Lab Universal Manual

Product: