Before starting and after end of a programme, the lamp
lights to show the the door can be opened. As long
as a wash programme is running, the door remains
locked and must on no account be forced open.
In case you have an urgent need to open it during a
running programme, refer to “Cancel (Reset) a running
programme before the end”.
PROGRAMME START
Open the tap and press the “Start/Pause” button.
The indication lamp next to the “Start/Pause” button
lights up. The programme sequence indicator shows the
current programme phase, running from left to right
through Wash, Rinse, Spin/Drain.
PROGRAMME END
•All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the
programme. The light blinks.
2. Select the new programme (with temperature), any
options and another spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
START DELAY
Add detergents as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
•Turn the programme selector to the desired
programme and temperature.
•The display shows the programme duration and the
predefined spin speed.
•The indication lamp next to the “Start/Pause”
button blinks.
The “Reset” button cancels a programme before the
end.
•Press and hold the “Reset” button for a few seconds.
Any existing water is drained out. It may last
some time until the door can be opened.
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating “Start delay” option.
•Select programme, temperature and options.
•Press the “Start delay” button to select the desired
delay time between 30 minutes and 23 hours.
•Press the “Start/Pause” button.
On the display, the start delay symbol and the dot
between hours and minutes blink. The countdown of
the delay time begins.
•The time delay indication disappears when the
programme starts and it is replaced by the remaining
programme time.
•Once having pressed the “Start/Pause” button,
the delay time can be reduced by pressing again the
“Start delay” button.
To cancel the “Start delay”
•Turn the programme selector to another position, or
press the “Start/Pause” button - the selected start
delay disappears from the display. Press “Start/
Pause” again if you want to start the selected
programme immediately.
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your “Instructions for Use”;
if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap: if the indications still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned: in the
latter case refer to the Instructions for Use (“Removing
the Filter”).
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with
respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer
to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Reference Programmes for Energy Label.
*** Automatic adaption of programme duration after detection of wash load.
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
without “Rapid”
(kWh)
Approx. Programme Duration (hrs : min)
without “Rapid”with “Rapid”
Cotton955.053*1.702:00-
Cotton **605.0440.754:002:30
Cotton **602.5320.652:20***
Cotton 405.0490.602:451:45
Cotton **402.5320.552:30***
Synthetics602.550*0.701:301:09
Synthetics402.5450.501:150:54
Sport302.5550.651:291:08
Delicates301.5500.500:45-
Daily load403.0450.451:00-
Quick wash303.0400.400:30-
Wool401.0550.600:45-
Handwash401.0450.600:40-
Lingerie301.0450.500:36-
Push the button(s) of any option(s) desired - the respe-
ctive indication lamp lights up.
When the combination of programme and additional op-
tion(s) is not possible, the indication lights switch off au-
tomatically. Unsuitable combinations of options are de-
selected automatically.
“Clean+” button
•Choose this option if you use an in-wash additive for
stain removal (powder, for example “Vanish”) - it will
optimize the additive’s efficiency to get better wash
performance and stain removal.
• Use with maximum load.
• Add an appropriate amount of in-wash additive for
stain removal (powder) to the main wash chamber,
together with your detergent (only use powder
detergent with this option).
Respect the manufacturer’s dosing instructions.
• Prolongs the programme by approx. 10 to 15
minutes.
• Appropriate for use of stain removers and bleaches
on oxygen basis. Chlorine or perborate bleaches
must not be used!
“Cold wash” button
• Water is heated only up to 20ºC.
• Suitable for delicate laundry items with wash
temperature recommendation of max. 30ºC on the
care label.
• Selectable only on the lowest temperature step
of each programme.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very
soft water, washing baby linen and helps people with
allergies.
“Easy ironing” button
• Can be used together with “Cotton”, “Synthetics”
and “Daily load” programmes to make ironing easier.
• Increases the water quantity and the clothes are spun
very gently.
“Rinse hold” button
•The laundry remains in the last rinse water without
pregressing to the final spin cycle to avoid creasing
and prevent colours from changing.
•It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
Note: The programme stops to “Rinse hold” at the
time the “Rinse hold” lights in the preogramme
sequence indication is on. The indication lamp next
to the “Start/Pause” button blinks.
Terminate the “Rinse hold” option:
•Press the “Start/Pause” button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
•If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain” programme
and press the “Start/Pause” button.
“Spin” button
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only.
“Prewash” button
•Only for heavily soiled loads (for example sand,
granular dirt). Increases the cycle time by
approximately 15 min.
•Do not use liquid detergent for the main wash when
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Polar PFL 1021-D at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Polar PFL 1021-D in the language / languages: English as an attachment in your email.
The manual is 0,46 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
