632185

Polar PFL 1000 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
5019 801 10027
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
Cotton 95 5.0 49* 1.90 2:00
Cotton 60 5.0 49 1.05 2:10
Cotton with “Eco”** 60 5.0 49 0.95 2:20
Cotton 40 5.0 49 0.60 2:00
Synthetics 60 2.5 50* 0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Delicates 30 1.5 50 0.50 0:45
Daily load 40 3.0 45 0.45 1:00
Quick wash 30 3.0 40 0.40 0:30
Wool 40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Add detergents as indicated on the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use. Close the door and turn the
programme selector to the desired programme and
temperature. The indication lamp next to the “Start/
Pause” button flashes.
CONSUMPTION DATA
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the
home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type
of wash.
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water
out.
** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the the door can be opened. As long
as a wash programme is running, the door remains
locked and must on no account be forced open.
In case you have an urgent need to open it during a
running programme, refer to “Cancel (Reset) a running
programme before the end”.
RED INDICATIONS
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your “Instructions for Use”;
if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap: if the indications still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned: in the
latter case refer to the Instructions for Use (“Removing
the Filter”).
“Intensive rinse” button
• More water is added and rinse cycle is prologned.
• This option is particularly suitable for areas with very
soft water, washing baby linen and helps people
with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
Note: The programme stops to “Rinse hold” at the
time the “Anticrease” light in the programme
sequence indicator is on. The indication lamp next
to the “Start/Pause” button flashes.
• If you select “Rinse Hold” do not leave items to soak
for too long.
Terminate the “Rinse hold” option:
• Press the “Start/Pause” button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain”
programme and press the “Start/Pause” button.
PROGRAMME START
Open the tap and press the “Start/Pause” button.
The indication lamp next to the “Start/Pause” button
lights up. The programme sequence indicator shows
the current programme phase, running from left to right
through Wash, Rinse, Spin/Drain.
When the programme phrase is finised, the
corresponding indication goes out.
PROGRAMME END
• All the lights of the programme sequence indicator
are off, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Select the new programme (with temperature), any
options and another spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the
end.
• Press the “Reset” button for at least 3 seconds.
Any existing water is drained out before the door
can be opened.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Eco” button
• With a modified temperature profile and a slightly
prologned washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
• Do not use liquid detergent for the main wash when
activating the Prewash option.
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
the rinse. The water is drained out only.
START DELAY
The “Start delay” allows to run the machine at the
consumer's convenience, for example at night when
electricity is cheaper.
• Select programme, temperature and options.
• Press the “Start delay” button to select the delay
time by 1, 3, 6, 9 or 12 hours.
• Press the “Start/Pause” button.
The indication next to the “Start delay” button lights
up and goes off when the programme starts.
• Once having pressed the “Start/Pause” button,
the countdown of the time delay begins. When the
programme starts, the start delay indicator light
goes off and is replaced by the programme sequence
indication.
• After the “Start/Pause” button has been pressed,
the number of hours preselected can be reduced by
pressing again the “Start delay” button.
• Do not use liquid detergent when activating the
Start delay.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
• Turn the programme selector to another position
or press the “Reset” button.
..after having pressed the “Start/Pause” button:
• Press the “Reset” button for at least 3 second - the
start delay indicator light goes out.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Polar PFL 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Polar PFL 1000 in the language / languages: English as an attachment in your email.

The manual is 4,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Polar PFL 1000

Polar PFL 1000 User Manual - English - 14 pages

Polar PFL 1000 User Manual - German - 13 pages

Polar PFL 1000 User Manual - Dutch - 13 pages

Polar PFL 1000 User Manual - Dutch - 13 pages

Polar PFL 1000 User Manual - French - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info