45213
5
Zoom out
Zoom in
Previous page
1/8
Next page
1*
2*
3*
4*5*
1 This product
2 Antenna jack
3 Fuse (10 A)
4 Note:
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
5 Connect leads of the same
color to each other.
6 Cap (1*)
Do not remove cap if this
terminal is not in use.
7 Yellow (3*)
Back-up
(or accessory)
8 Yellow (2*)
Connect to the constant 12 V supply
terminal.
9 Red (5*)
Accessory
(or back-up)
10 Red (4*)
Connect to terminal controlled by
ignition switch (12 V DC).
11 Black (chassis ground)
Connect to a clean, paint-free metal location.
12 ISO connector
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to
connect to both connectors.
13 Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Green: Rear left
Green/black: Rear left
Violet: Rear right
Violet/black: Rear right
<YRD5142-A/S>6
Connections
En
<YRD5142-A/S> 17
Fig. 1
Abb. 1
Afb. 1
Рис. 1
14 Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
16 Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
15 Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
17 Blue/white (7*)
Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).
18 Blue/white (6*)
The pin position of the ISO connector will differ depends
on the type of vehicle. Connect 6* and 7* when Pin 5 is
an antenna control type. In another type of vehicle, never
connect 6* and 7*.
<YRD5142-A/S>7
Connections
En
<YRD5142-A/S> 18
Important
! When this unit is installed in a vehicle without
ACC (accessory) position on the ignition
switch, red cable must be wired to the term-
inal that can detect the operation of the igni-
tion key. Otherwise, battery drain may result.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC position No ACC position
! Use of this unit in conditions other than the
following could result in fire or malfunction.
Vehicles with a 12-volt battery and negative
grounding.
Speakers with 50 W (output value) and 4
ohm to 8 ohm (impedance value).
! To prevent a short-circuit, overheating or mal-
function, be sure to follow the directions
below.
Disconnect the negative terminal of the
battery before installation.
Secure the wiring with cable clamps or ad-
hesive tape. To protect the wiring, wrap ad-
hesive tape around them where they lie
against metal parts.
Place all cables away from moving parts,
such as gear shift and seat rails.
Place all cables away from hot places,
such as near the heater outlet.
Do not pass the yellow cable through a
hole into the engine compartment to con-
nect to a battery.
Cover any disconnected cable connectors
with insulating tape.
Do not shorten any cables.
Never cut the insulation of the power cable
of this unit in order to share the power
with other devices. Current capacity of the
cable is limited.
Use a fuse of the rating prescribed.
Never wire the speaker negative cable di-
rectly to ground.
Never band together multiple speakers ne-
gative cables.
! Control signal is output through blue/white
cable when this unit is powered on. Connect it
to an external power amps system remote
control or the vehicles auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
vehicle is equipped with a glass antenna, con-
nect it to the antenna booster power supply
terminal.
! Never connect blue/white cable to external
power amps power terminal. Also, never con-
nect it to the power terminal of the auto anten-
na. Otherwise, battery drain or malfunction
may result.
! Black cable is ground. This cable and other
products ground cable (especially, high-cur-
rent products such as power amp) must be
wired separately. Otherwise, fire or malfunc-
tion may result if they are accidentally de-
tached.
Connection Diagram (Fig. 1)
1 This product
2 Antenna jack
3 Fuse (10 A)
4 Note:
Depending on the kind of vehicle, the function
of 3* and 5* may be different. In this case, be
sure to connect 2* to 5* and 4* to 3*.
5 Connect leads of the same color to each
other.
6 Cap (1*)
Do not remove cap if this terminal is not in
use.
7 Yellow (3*)
Back-up (or accessory)
8 Yellow (2*)
Connect to the constant 12 V supply terminal.
9 Red (5*)
Accessory (or back-up)
<YRD5142-A/S>8
Connections
En
<YRD5142-A/S> 19
10 Red (4*)
Connect to terminal controlled by ignition
switch (12 V DC).
11 Black (chassis ground)
Connect to a clean, paint-free metal location.
12 ISO connector
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to con-
nect to both connectors.
13 Speaker leads
White: Front left +
White/black: Front left *
Gray: Front right +
Gray/black: Front right *
Green: Rear left +
Green/black: Rear left *
Violet: Rear right +
Violet/black: Rear right *
14 Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
15 Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
16 Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
17 Blue/white (7*)
Connect to auto-antenna relay control term-
inal (max. 300 mA 12 V DC).
18 Blue/white (6*)
The pin position of the ISO connector will dif-
fer depends on the type of vehicle. Connect 6*
and 7* when Pin 5 is an antenna control type.
In another type of vehicle, never connect 6*
and 7*.
<YRD5142-A/S>9
Connections
En
<YRD5142-A/S> 20
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer DEH-1020E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer DEH-1020E in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pioneer DEH-1020E

Pioneer DEH-1020E User Manual - English, German, Dutch, French, Italian, Spanish - 107 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info