491895
6
Zoom out
Zoom in
Previous page
1/100
Next page
02 Connecting up
6
En
When using speakers with removable network
circuits, note that if the network is removed, no
effect will be produced and damage may be caused
to the speaker.
Another method of connection is to connect the
SPEAKERS A terminals to HIGH and the SPEAKERS
B terminals to LOW (reverse that shown in the
illustration).
Connecting speaker cables
1 Twist the cable cores.
2 Loosen the nut on the
SPEAKERS
terminal, and insert the speaker cable into
the exposed hole in the terminal shaft.
3 Retighten the terminal nut.
Caution
When using only one set of speaker terminals
(SPEAKERS A or SPEAKERS B), or when utilizing
bi-wiring connections, the speaker used should
have a nominal impedance between 4 Ω and
16 Ω. When using both sets of terminals, the
connected speakers should have nominal
impedance between 8 Ω and 32 Ω. Consult the
instructions accompanying your speakers for
details regarding the impedance value.
Make sure the positive and negative (+/–) terminals
on the amplifier match those on the speakers.
These speaker terminals carry HAZARDOUS live
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
Make sure that all the bare speaker wire is twisted
together and inserted fully into the speaker
terminal. If any of the bare speaker wire touches the
back panel it may cause the power to cut off as a
safety measure.
Connecting audio cables
Connect the white plug to the left (L) jack, and the red
plug to the right (R) jack. Be sure to insert the plugs fully
into the jacks.
123
10 mm
Left (white)
Right (red)
Using centralized control with other
Pioneer components
Multiple Pioneer components equipped with CONTROL
IN/OUT jacks can be connected to the unit, allowing
centralized control of the components via the remote
sensor on the unit. This also allows remote control of
components not equipped with a remote sensor, or
installed in places where the component’s remote
sensor cannot be accessed.
Note
For connections use a commercially available
monaural miniplug cord (without resistor).
When connecting the CONTROL IN/OUT jacks,
commercially available audio cords must also be
used to make analog connections. Merely
connecting the CONTROL IN/OUT jacks alone will
not allow proper system control.
When a control cord is connected to the unit’s
CONTROL IN jack, the unit cannot be controlled by
pointing the remote control at the unit (the remote
sensor is automatically disabled).
Digital audio input connections (A-70
only)
If a coaxial digital cable (sold separately) is used to
connect this unit’s DIGITAL IN COAXIAL terminal to the
digital audio output connector of a digital audio playback
component, the playback component can be used to
play music through this unit.
For more information regarding the output of audio
signals input to the DIGITAL IN COAXIAL terminal,
consult page 12.
Note
Digital signal formats that can be input to this unit
include linear PCM signals with sampling rate and
quantitative bits up to 192 kHz/32 bits. (Depending
on the connected device and environment,
operation may not be successful).
IN
OUT
CONTROL
DIGITAL OUT
COAXIAL
Digital audio
equipment, etc.
Coaxial digital audio cable
(sold separately)
A-70’s rear panel
A70_SYXE8.book 6 ページ 2012年7月27日 金曜日 午後6時53分
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pioneer A70-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pioneer A70-S in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 18,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info