492013
5
Zoom out
Zoom in
Previous page
1/7
Next page
Elite Amplier Owners Manual
© 2012 Phoenix Gold • www.phoenixgold.com
© 2012 Phoenix Gold • www.phoenixgold.com
Elite Amplier Owners Manual
All crossover frequency potentiometers have 41 detents or clicks” so the end user can set the exact crossover frequency desired.
ELITE.1
clicks
Subsonic
(10~55Hz)
LPF
(30~300Hz)
1 12 30
2 12 30
3 12 30
4 12 30
5 12 30
6 12 31
7 13 32
8 13 33
9 14 35
10 15 37
11 16 39
12 16 42
13 18 45
14 19 49
15 20 52
16 22 56
17 24 62
18 26 69
19 28 77
20 31 87
21 32 102
22 34 114
23 35 120
24 36 126
25 38 134
26 39 143
27 40 152
28 42 163
29 44 214
30 45 230
31 47 248
32 47 251
33 48 253
34 48 260
35 49 273
36 49 280
37 49 289
38 49 295
39 50 304
40 50 305
41 50 306
CROSSOVER SETTINGS
ELITE.2
clicks
LPF
(40Hz~4khz)
HPF
(20Hz~4kHz)
1 37 23
2 37 24
3 38 24
4 38 25
5 41 27
6 44 29
7 48 30
8 51 31
9 56 33
10 62 37
11 68 40
12 76 44
13 88 50
14 96 55
15 110 58
16 130 67
17 160 78
18 180 99
19 190 120
20 220 121
21 250 150
22 290 170
23 330 200
24 360 220
25 430 260
26 480 360
27 560 390
28 620 430
29 720 450
30 970 631
31 1.18k 790
32 1.3k 890
33 1.5k 1k
34 1.7k 1.18k
35 2k 1.4k
36 2.45k 1.7k
37 2.7k 2.2k
38 3.2k 3.2k
39 3.5k 4.15k
40 3.85k 4.2k
41 3.9k 4.4k
ELITE.4
clicks
LPF
(40Hz~4kHz)
HPF
(20Hz~4kHz)
1 36 24
2 37 25
3 38 27
4 41 30
5 44 33
6 48 38
7 52 41
8 55 46
9 61 51
10 65 60
11 67 71
12 73 83
13 86 96
14 93 106
15 99 122
16 107 129
17 127 134
18 162 143
19 186 155
20 220 170
21 251 187
22 282 207
23 317 235
24 365 264
25 430 286
26 517 330
27 666 353
28 860 393
29 1.05k 434
30 1.12k 455
31 1.32k 514
32 1.49k 583
33 1.65k 693
34 1.77k 876
35 2k 1k
36 2.3k 1.2k
37 2.5k 1.4k
38 2.9k 1.8k
39 3.2k 2.6k
40 3.6k 3k
41 3.9k 4.2k
FRONT AND REAR INPUTS
Connect preamp signal cables from headunit to these inputs. The front
and rear inputs must be used, if only the front input is used then the rear
speaker outputs will have no output signal.
FAN
The internal fan is nearly inaudible but the end user can control the fans
mode via the endpanel switch.
ON:
Fan runs at full speed at all times regardless of the heatsink
temperature. This is recommended for heavy users or low impedance
loads such as 1 ohm stereo/2 ohms bridged.
OFF:
Internal fan is o. This is only recommended for short periods of
time. For example, a sound quality competition.
AUTO:
Best setting for most users. Internal fan is o until the heatsink
temperature reaches 50°c/120°F then the variable fan turns on and its
speed is controlled by the heatsink temperature.
REMOTE LEVEL CONTROL
This port is for connecting the subwoofer remote level control. This is not a bass
boost, it controls the level of the low pass signal of
rear channels only
. Rear channels’
cong switch must be set to “LP/BP” for the remote to operate.
CROSSOVER FREQUENCY
Controls the crossover point for the speaker outputs. See page 8 for exact crossover
settings.
LEVEL
Used to reach maximum amplier power with a wide variety of headunits.
CONFIG
FLAT:
Crossovers are turned o
HP:
High pass crossover is on
LP/BP:
Low and High Pass crossovers are on, creating a Bandpass (BP) setting for
midbass drivers or subwoofers. For a standard subwoofer system, the high pass
frequency now becomes a subsonic lter. To turn subsonic lter o, turn the HP
FREQ (Subsonic Filter) to 20Hz.
+12V
This must be connected to the fused positive terminal (+12V) of the cars
battery. The fuse must be located within 18 inches of the battery.
REMOTE
This must be connected to switched +12V, usually a trigger wire coming
from the head unit or ignition.
GROUND
This must be connected to the negative terminal of the car’s battery or
bolted to a clean, unpainted part of the chassis of the vehicle.
RMD
Optional RMD Voltage Display plugs into this port. Sold separately.
CLIP INDICATOR
Lights when the amplier reaches near maximum output. Under normal
operation the clip indicator should be ashing during the peaks of the
music. The clip indicator should not stay lit for long periods of time (more
than 2 or 3 seconds), if this is the case you need to reduce system volume
or level of the amplier.
PROTECT INDICATOR
Lights red if there is a problem with the audio system. For example, speaker
wire is pinched/shorted, the amplier is running too low of an impedance
or reached an unsafe temperature.
SPEAKER OUTPUTS
Used to connect the amplier to speakers. Minimum impedance is 2 ohms
bridged or 1 ohm stereo. Minimum speaker wire size is 16 gauge. Use Left
+ and Right - to bridge the channels.
ELITE.4 FUNCTIONS
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Phoenix Gold Elite at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Phoenix Gold Elite in the language / languages: English as an attachment in your email.

The manual is 5,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info