Manual Philips GC1026 (page 2 of 10) (English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish)

537752

Zoom out

Zoom in

1/10

ENGLISH

General description (Fig. 1)

1 Spray nozzle

2 Capofllingopening

3 Steam control

- CALC CLEAN = Calc-Clean function

- t=dryironing

- ECO = optimal steam

- ; = maximum steam

= turbo steam

4 Steam boost button

5 Spray button

6 Temperature dial

7 Temperaturelight

8 Mains cord

9 Type plate

10 WatertankwithMAXwaterlevelindication

11 Soleplate

Using the appliance

Filling the water tank

Note: Your appliance has been designed to be used with tap water. If you live in an area with very hard water,

fast scale build-up may occur. In this case, it is recommended to mix 50% distilled water and 50% tap water to

prolong the lifetime of your appliance.

Note: Do not put perfume, vinegar, starch, descaling agents, ironing aids, chemically descaled water or other

chemicals in the water tank.

1 Set the steam control to position t (dry ironing). (Fig. 2)

2 Fill the water tank up to the MAX indication (Fig. 3).

3  Closethecapofthellingopening.

Selecting temperature and steam setting

Table 1

Fabric type Temperature

setting

Steam

setting

Steam

boost

Spray

Linen MAX

Ye s Yes

Cotton

Ye s Ye s

Wool

ECO No Ye s

Silk

t No No

Syntheticfabrics

(e.g.acrylic,nylon,

polyamide, polyester).

t No No

1 Consult table 1 to set the temperature dial to the appropriate setting for your garment (Fig. 4).

2 Put the iron on its heel and plug it in. The temperature light goes on to indicate that the iron is

heating up (Fig. 5).

3 When the temperature light goes out, the iron has reached the correct temperature.

4 Consult table 1 to select a steam setting that corresponds to the temperature you have set (Fig. 6).

Note: To use turbo steam

, keep the steam control pressed to the turbo steam position continuously.

Caution: Do not set the steam control to a steam setting if the set temperature is below 2 or when

the iron is still heating up (when the temperature light is on). Otherwise water may leak from the iron.

Features

Spray function

- Pressthespraybuttontomoistenthearticletobeironed.Thishelpsremovestubborncreases(Fig.7).

Steam boost function

- Pressandreleasethesteamboostbuttonforapowerfulboostofsteamtoremovestubborn

creases(Fig.8).

Vertical steam

Youcanusethesteamboostfunctionwhenyouholdtheironinverticalpositionforremovingcreases

fromhangingclothes,curtainsetc(Fig.9)

ECO steam setting

- SelecttheECOsteamsettinginsteadofthemaximumsteamsetting;tosaveenergy,yettoachieve

satisfactoryironingresults.(Fig.10)

Dry ironing

- Setthesteamcontroltot(dryironing)toironwithoutsteam.(Fig.2)

Cleaning and maintenance

Cleaning

1 Set the steam control to t (dry ironing), unplug the iron and let it cool down. (Fig. 2)

2 Pour any remaining water out of the water tank.

3  Wipeakesandanyotherdepositsoffthesoleplatewithadampclothandanon-abrasive(liquid)

cleaning agent.

Caution: To keep the soleplate smooth, avoid hard contact with metal objects. Never use a scouring pad,

vinegar or other chemicals to clean the soleplate.

Note: Regularly rinse the water tank with tap water. Empty the water tank after rinsing it.

Calc-Clean function

IMPORTANT: To prolong the lifetime of your appliance and to maintain good steaming

performance, use the Calc-Clean function once every two weeks. If the water in your area

is very hard (i.e. when akes come out of the soleplate during ironing), use the Calc-Clean

function more frequently.

1 Make sure the appliance is unplugged and the steam control is set to t (dry ironing). (Fig. 2)

2 Fill the water tank to the MAX indication. (Fig. 3)

Do not pour vinegar or other descaling agents into the water tank.

3 Plug in the iron and set the temperature dial to MAX (Fig. 11).

4 Unplug the iron when the temperature light goes out.

5  Holdtheironoverthesink.PushthesteamcontroltotheCalc-Cleanpositionandholdit.(Fig.12)

6 Gently shake the iron until all water in the water tank has been used up (Fig. 13).

Caution:Whilescaleisushedout,steamandboilingwateralsocomeoutofthesoleplate.

7 Set the steam control back to t (dry ironing). (Fig. 2)

Note: Repeat the Calc-Clean process if the water that comes out of the iron still contains scale particles.

After the Calc-Clean process

1 Plug in the iron. Let the iron heat up to let the soleplate dry.

2 Unplug the iron when the temperature light goes out.

3 Move the iron gently over a piece of cloth to remove any water stains on the soleplate.

4 Let the iron cool down before you store it.

Storage

1 Unplug the iron and set the steam control to t (dry ironing). (Fig. 2)

2 Wind the mains cord round the cord storage facility and store the iron on its heel (Fig. 14).

Troubleshooting

Thischaptersummarisesthemostcommonproblemsyoucouldencounterwiththeappliance.Ifyou

areunabletosolvetheproblemwiththeinformationbelow,visitwww.philips.com/supportforalistof

frequentlyaskedquestionsorcontacttheConsumerCareCentreinyourcountry(seetheworldwide

guaranteeleaetforcontactdetails).

Problem Possible cause Solution

Waterdripsfromthe

soleplate or wet spots

appearonthegarment

duringironing.

Thesettemperatureistoo

lowforsteamironing.

Setanironingtemperaturethatis

suitableforsteamironing.Seetable1.

Youhaveputanadditivein

thewatertank.

Rinsethewatertankanddonotputany

additiveinthewatertank.

Thesteamboostfunction

does not work properly

(waterleaksoutofthe

soleplate).

Youhaveusedthesteam

boost function too often

withinaveryshortperiod.

Waitawhilebeforeyouusethesteam

boostfunctionagain.

Youhaveusedthesteam

boost function at a too low

temperature.

Setanironingtemperatureatwhich

thesteamboostfunctioncanbeused

( 2toMAX).

Flakesandimpuritiescome

outofthesoleplateduring

ironing.

Hardwaterformsakes

insidethesoleplate.

UsetheCalc-Cleanfunction(seechapter

‘Cleaningandmaintenance’,section

‘Calc-Cleanfunction’).

Waterdripsfromthe

soleplateaftertheironhas

cooleddownorhasbeen

stored.

Youhaveputtheironin

horizontalpositionwhile

therewasstillwaterinthe

water tank.

Emptythewatertankandsetthesteam

controltoposition‘dry’afteruse.Store

theirononitsheel.

Waterleaksfromthecapof

thellingopening.

Youhaveoverlledthe

water tank.

Donotllthewatertankbeyondthe

MAXindication.Pourexcesswaterout

ofthewatertank.

WhenIpushthesteam

controltotheturbosteam

position,thesteamcontrol

jumps back.

Youdidnotkeepthesteam

controlintheturbosteam

position.

Ifyouwanttouseturbosteam,youhave

tokeepthesteamcontrolintheturbo

steampositioncontinuously.Forother

steamsettings,thisisnotnecessary.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Philips GC1026 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Philips GC1026 Manual

Product: