751165

Philips DES9900 Manual

38
Zoom out
Zoom in
Previous page
1/240
Next page
GB5 WelcomeEye Connect / Touch / 09/17
5. PRODUCT INSTALLATION
Important notes and advice:
- To make the most of your intercom panel, we recommend conguring it (RFID, for 1 or 2
families, 1 or 2 intercoms, loudspeaker volume) before nal installation. To do this, a table
connection may be necessary to check that the settings are correct.
- If you test your product before installing it, ensure that you do not test it with the intercom
panel and the monitor in the same room to avoid the video doorphone emitting a shrill
noise (feedback).
- Do not expose the camera lens to direct sunlight or a reective surface.
- We recommend running the cables through a protective sheath to protect them against
breakage and bad weather.
- For the WelcomeEye Connect version, to make the most of your monitor’s Wi-Fi function,
we advise you to check that your Wi-Fi network is accessible from where it is installed.
1. Wiring
To avoid the risk of interference and malfunctions, do not run the videophone cable through
the same sheath as the electrical cables.
Warning: Do not double up the wires to increase their section.
a. Connecting the videophone (monitor, intercom panel and camera)
Wires to be used: two wires 0.75mm2 with 80m length or two wires 1.5mm2 with 120m length.
- Make sure to connect the wires in accordance with one of the wiring diagrams depending
on the desired conguration.
- Refer to the label stuck to the back of the monitor and the back of the intercom panel.
- Congure the switches on the back of the intercom panel as well as the monitor interface
according to the chosen conguration (see section 2 intercom conguration).
b. Connecting a gate motor
- The intercom provides a dry contact (without power) to be connected to the push button
control of the automatic opener.
- Connect it directly to terminals 5 and 6 at the back of the intercom panel (no need to
observe polarity).
- The opening function is only possible if the video of the respective intercom panel is
displayed.
c. Connecting a strike plate or electric lock
Important: The strike plate or electric lock that you are ordering must have a mechanical
memory. The strike plate current cannot exceed 1.1A.
- Connect it directly to terminals 7 and 8 at the back of the intercom panel (no need to
observe polarity).
- The opening function is only possible if the video of the respective intercom panel is
displayed.
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips DES9900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips DES9900 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info