328
28
Zoom out
Zoom in
Previous page
1/30
Next page
Notes:
If the Temperature warning indicator lights up, follow the
above possible solutions and then wait until the projector has
cooled down completely before turning the power back on.
(At least 5 minutes.)
If the power is turned off and then turned on again, as during
a brief rest, the Lamp indicator may be triggered, preventing
the power from going on. Should this occur, take the power
cord out of the wall outlet and put it back in again.
Lamp (LCA 3110; 8670 931 10009)
The lamp in this projector operates for approximately 2000
cumulative hours, depending on the usage environment. It is
recommended that the lamp be replaced after 1900 cumulative
hours of use or when you notice a significant deterioration of
the picture and colour quality. The lamp usage time can be
checked with the On-screen Display
(see page 23).
CAUTION!
Intense light hazard. Do not attempt to look into the aperture
and lens while the projector is operating.
As the usage environment can vary significantly, the
projector lamp may not operate for 2000 hours.
Replacing the lamp
1.
Unplug the power cord.
Press Power OFF. Wait until the cooling fan stops.
2.
Disconnect the powercord
Disconnect the mains lead and all the other cables.
3.
Slide the lamp cage cover out.
Turn over the projector and unfasten the user service screw
that secures the lamp cage cover. Then slide the cover in
the direction of the arrow.
4.
Remove the lamp cage.
Remove the securing screws from the lamp cage.
Hold the lamp cage by the handle and pull it towards you.
5.
Replace the lamp cage (after changing the lamp).
Press the lamp cage firmly into the lamp cage
compartment. Fasten the securing screws.
6.
Slide the lamp cage cover in.
Slide the lamp cage cover in the direcrtion of the arrow.
Then fasten the user service screw.
CAUTION!
Do not remove the lamp cage directly after operation of the
projector. The lamp may be extremely hot. Wait at least one
hour after the power cord is disconnected to allow the
surface of the lamp cage to fully cool before removing the
lamp cage.
Be sure to remove the lamp cage by the handle. Be sure not
to touch the glass surface of the lamp cage or the inside of
the projector.
26
9. ADDITIONAL INFORMATION Maintenance
English
Maintenance Indicator Condition Problem Possible Solution
TEMP. The internal Blocked air intake. Relocate the projector to an area with
WARNING indicator temperature is proper ventilation.
(Temp) abnormally high. Clogged air filter. Clean the filter.
(see page 25.)
Cooling fan breakdown. Take the projector to your nearest
Internal circuit failure. Authorized Philips Industrial LCD
Products Dealer or Service Center for
repair.
LAMP indicator The lamp does not Burnt-out lamp. Carefully replace the lamp.
(Lamp) light up Lamp circuit failure. (See page 26.)
Take the projector to your nearest
Authorized Philips Industrial LCD
Products Dealer or Service Center for
repair.
POWER INDICATOR The POWER indicator The bottom filter cover Securely install the bottom filter cover.
z / y flashes in red when the is open.
projector is on.
Securing screws
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philips Bsure 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philips Bsure 1 in the language / languages: English, Dutch as an attachment in your email.

The manual is 3,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Philips Bsure 1

Philips Bsure 1 User Manual - English - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info