492066
20
Zoom out
Zoom in
Previous page
1/21
Next page
Power Failure
If there is a power failure the wash cycle will be interrupted, and the wash programme
and functions will be suspended. When the power is restored, the wash programme
and functions will re-start from the same point and complete the programme.
During a power failure the water can be drained and the load can be removed from
the machine as follows:
Step 1. Switch off the machine both via the programme dial and the mains power
supply. Remove the plug from the mains power supply socket.
Step 2. Carefully move the machine so the rear of the machine is accessible. Please
follow the safety precautions that we recommend under the Warning and Safety
Instructions section of this manual.
Step 3. Unclip the drain hose from the rear panel of the machine and lower the hose
into a bowl on the floor. When the bowl is full raise the end of the drainpipe to a
height higher than the top of the appliance to stop the flow of water. Empty and
replace the bowl and continue draining the machine until empty.
Step 4. Once the machine is fully drained of water, clip the hose to the rear of the
machine. Open the door and remove the load.
The door can be opened approximately 2 minutes after the power failure.
Do not force open the door.
75
Problem with the dispenser…
Not all the detergent has been flushed away.
1. Check the water supply tap is fully turned on.
2. Check the inlet hose is not kinked.
The dispenser drawer will not close properly.
1. Check the drawer is aligned properly
2. Check the drawer is not clogged with detergent (see Care and
Maintenance)
Steam is coming from the dispenser. The machine is designed to vent through the
drawer, this is nothing to worry about.
The clothes load is not dry…_
Was sufficient time or automatic setting selected to dry the clothes load? (Refer to
Drying Time Guide page 69.)
Is the wash programme selected followed automatically by a drying programme?
(Refer to Programme Guide page 60.)
Was the laundry correctly spun prior to drying? Select a spin programme to
remove the excess water.
Has the correct drying programme been selected? Refer to the laundry care label
for guidance.
The laundry may have been excessively wet at the end of the wash cycle eg. The
load was out of balance (see page 56). In this case the load may not have dried
within the maximum time allowed. Select a drying only programme (page 59) to
complete the drying.
Remember, you may be charged for the service call if incorrect installation or misuse
causes a problem with your machine.
Note: The use of environmentally friendly, phosphate-free detergents (check detergent
information on pack) can have the following effects:
Waste water from rinsing may be cloudier because of the presence of a white
powder (zeolites) held in suspension, without the rinse performance being adversely
affected.
Presence of white powder on laundry after washing, which is not absorbed by
the fabric and does not alter the colour of the fabric.
The presence of foam in the final rinsing water is not necessarily an indication of
poor rinsing. Carrying out more rinse cycles does not serve any purpose in such
cases.
74
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Philco PWD14S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Philco PWD14S in the language / languages: English as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info