78023
88
Zoom out
Zoom in
Previous page
1/90
Next page
If the door does not close correctly, loosen
or tighten the adjustable feet until the ma-
chine is perfectly level.
Water connection
Water inlet connection
This appliance can be connected to either a
hot (max. 60°) or cold water supply.
With a hot water supply you can have a sig-
nificant reduction of energy consumption.
This however, depends on how the hot water
is produced. (We suggest alternative sources
of energy that are more environmentally
friendly as e.g. solar or photovoltaic panels
and aeolian).
For making the connection itself, the cou-
pling nut fitted to the appliance water inlet
hose is designed to screw onto a 3/4" thread
spout or to a purpose made quick-coupling
tap such as the Press-block.
The water pressure must be within the limits
given in the 'Technical data'. Your local Wa-
ter Authority will advise you on the average
mains pressure in your area.
The water inlet hose must not be kinked,
crushed, or entangled when it is being con-
nected.
The locknut must be correctly fitted to avoid
water leaks.
If the appliance is connected to new pipes or
pipes which have not been used for a long
time, you should run the water for a few mi-
nutes before connecting the inlet hose.
Do not use connection hoses which
have previously been used on an old ap-
pliance.
This appliance has been fitted with safe-
ty features which will prevent the water
used in the appliance from returning
back into the drinking water system. This
appliance complies with the applicable
plumbing regulations.
Water inlet hose with safety valve
After connecting the double-walled water in-
let hose, the safety valve is next to the tap.
Therefore the water inlet hose is only under
pressure while the water is running. If the wa-
ter inlet hose starts to leak during this oper-
ation, the safety valve cuts off the running
water.
Please take care when installing the water
inlet hose:
The electrical cable for the safety valve is
in the double-walled water inlet hose. Do
not immerse the water inlet hose or the
safety valve in water.
If water inlet hose or the safety valve is
damaged, remove the mains plug imme-
diately.
A water inlet hose with safety valve must
only be replaced by the Service Force
Centre.
Warning! Dangerous voltage
Water drain connection
The end of the drain hose can be connected
in the following ways:
1. To the sink outlet spigot, securing it to the
underside of the work surface. This will
prevent waste water from the sink run-
ning into the machine.
2. To a stand pipe provided with venthole,
minimum internal diameter 4 cm.
max 85 cm
min 40 cm
max 400 cm
The drain hose can face either to the right or
left of the dishwasher
Ensure the drain hose is not bent or squash-
ed as this could prevent or slow down the
discharge of water.
88
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pelgrim GVW 567 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pelgrim GVW 567 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 8,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info